New: Buy Now on Thomas and Pay Over Time with Credit Key   Learn More

2- and 3-Way Solenoid Valve is suitable for corrosive fluids.

2- and 3-Way Solenoid Valve is suitable for corrosive fluids.

Miniature Isolation Valve is rated up to 35 PSI, Cv=.05. It is availabe in 12 VDC and 24 VDC models, normally open or normally closed with numerous port options. Materials in contact with flow path are limited to PEEK and EPDM or FKM-GF. Seat and diaphragm design provides long life exceeding 15 million cycles.

Read More »
Inert Diaphragm Valve handles aggressive fluids.

Inert Diaphragm Valve handles aggressive fluids.

Three-way IDV solenoid-operated diaphragm isolation valve works with fluids found in medical equipment, water purification and clinical chemistry industries. Materials of all surfaces in flow path are inert and impervious to many aggressive fluids. Valve is typically used in waste circuits where valve must tolerate high contaminant levels. Valve is rated 35 psi with Cv of 0.22 and is available in...

Read More »
Through-port Valves control and shut off flow.

Through-port Valves control and shut off flow.

Stargate-O-Port valves work with ultrasonic positioner to control flow. Different port and orifice shapes allow selecting certain characteristics of flow cross section and blade position. Valves also serve as line blind in maintenance situations, to take out pipes and set blank flanges for safety. They have tight class VI shut-off which allows operators to close valve, inset locking pin and pad...

Read More »
Isolation Valve mounts directly on manifold.

Isolation Valve mounts directly on manifold.

Two-way solenoid valve mounts on manifold, is rated up to 35 psi with Cv of 0.05, and is available in 12 and 24 Vdc models, in normally open or normally closed versions. Materials in contact with flow path are limited to PEEK (polyetheretherketone) and EPDM (ethylene propylene) or FKM (highly-fluorinated fluorocarbon). Applications include blood analysis, clinical chemistry, DNA processing,...

Read More »
Inert Valve controls corrosive or high-purity fluids.

Inert Valve controls corrosive or high-purity fluids.

Solenoid-operated IPV inert proportional diaphragm isolation valve can be used in medical equipment, water purification and clinical chemistry industries. Materials of all surfaces in flow path are inert and impervious to wide range of aggressive fluids. Valve provides infinitely variable flow control, is rated to 60 psi, and has 24 Vdc driver. Poppet and seat are configured to provide bubble...

Read More »
Dispense Valve features drip-free cutoff.

Dispense Valve features drip-free cutoff.

Pneumatically operated 752V-UHSS dispense valve has no seals or O-rings to wear out. Amount dispensed is determined by combination of fluid flow rate and valve open time. Adjustable stroke control allows flow rate to be fine tuned, while open time is regulated in increments from 0.01 to 0.001 seconds with EFD VALVEMATE(TM) controller. Applications include automated assembly machines, XYZ tables,...

Read More »
Molded High-Flow 2-Way Valve uses no O-ring end fittings.

Molded High-Flow 2-Way Valve uses no O-ring end fittings.

Created for use in high purity/corrosive chemical applications, injection-molded Furon-® In-Line-1000 Valve provides true 1 in. orifice and angled actuator that promotes maximum flow (Cv-15). It is offered in pneumatically or manually actuated versions, and has maximum operating pressure and maximum back pressure ratings of 100 psi. Fluid temperature ranges from 40-

Read More »
Multi-Port Check Valves operate in any orientation.

Multi-Port Check Valves operate in any orientation.

Used to control flow in vacuum or pressure lines, check valve permits flow in one direction only and prevents flow in opposite direction. Valves are manufactured with nylon bodies and fluorosilicone seals, operate in any orientation, and can be used for liquid service. Standard barbs are available in 3/16, 5/16 and 1/4 in. ID. Other barb sizes as well as thread or bulkhead fittings can be adapted...

Read More »
Diaphragm Valves withstand corrosive environments.

Diaphragm Valves withstand corrosive environments.

All-plastic diaphragm valves for 3, 4 and 6 in. pipelines are suitable for control of liquids, gases, and slurries in both on/off and modulating services. Each has handwheel that opens or closes valve with minimal effort. Plastic valves will never fail, jam, stick, or freeze in position because of rust or corrosion; will never contaminate sensitive process fluids; and never need to be painted or...

Read More »
Plastic Valves assemble easily into manifolds.

Plastic Valves assemble easily into manifolds.

RDVM-1000 injection molded, Furon rolling diaphragm two-way valve and SMDVM-1000 1 in. self manifolding distribution valve have 100% PFA HP and Virgin PTFE wetted flow paths, visual position indicators, no exposed metallics, leak detection ports,and quick-release, non-metallic, eight-position mounting base. Both are available in pneumatically or manually actuated versions. Universal non-gender...

Read More »

All Topics