Feeder delivers lubrication to tablet presses.
Available in volumetric and gravimetric models, Tablet Press Lubricant Feeder features specialized gas venturi for aspiration of lubricant, such as magnesium stearate, directly to tablet press. It offers automated, nearly constant feed rate, providing uniform coating of tablet tools and avoiding sticking problems. Use of gravimetric model enables validation of product mass flow.
Read More »Wire Feeder uses MaxTrac(TM) heavy-duty wire drive system.
Suited for MIG and metal- or flux-cored wire welding, LF-74 delivers positive arc starting and feeding with stainless steel and aluminum. Its 4-roll MaxTrac(TM) cast aluminum wire drive system delivers consistent feeding force. Accommodating 0.023-1/16 in. MIG wire diameters and .030-5/64 in. flux-cored wire diameters, unit offers feed speeds of 50-800 ipm. Split wire guides provide full support...
Read More »
Automatic Bar Feed offers 4 minute changeovers.
Using oil-based, hydrostatic support system, Quick Six handles 18 in. to 6 ft long bar stock ranging from 5/16-3 1/8 in. diameter. Menu-driven remote control prompts users through setups, and program data is stored on smart media cards. Standard chain magazine holds 8 pieces of bar stock, and optional side load rack and bar elevator holds up to 50 6-ft bars.
Read More »
Process Controller suits seam welding of thin gauge metals.
CSC MIG welding controller utilizes controlled short circuit gas metal arc welding process to clear short circuits by retracting wire from short. Controller syncronizes wire feeder actions with power supply current to continuously feed wire alternatly between forward and reverse directions. Process helps to increase travel speed and eliminate spatter on wide range of materials including steel,...
Read More »
Design & Manufacturing Process of a Coil
Because the design and manufacturing of electromagnets are critical to the successful operation of the application, it's important to spend time defining your requirements before purchasing coils for an application. This eBook will guide you through the process of evaluating the application's constraints, identifying the needed specifications, and collaborating with a manufacturer to develop an appropriate coil solution for the application.
Read More »Welding System is available in various configurations.
Ready-Pak(TM) kits are available in 4 configurations with various power sources to meet application needs. All kits include LF-72 wire feeder featuring 2-roll MaxTrac(TM) drive system for accurate wire feeding. Other components are power source, drive rolls and wire guide, wire feeder control cable, welding gun, work lead and clamp, and HarrisÃ-® Flowmeter/Regulator and gas hose. Two kits...
Read More »Dispenser is suited for compound management and logistics.
FlexiWeigh 1000 and 2000 offer capabilities for powder and solvent dispensing, inerting of target containers, and capping/uncapping in addition to labeling, sample tracking, and weighing. Floor-standing, fully enclosed cabinets are equipped with XYZ robot with rotating arm and WISC module, which can combine multiple operations at one vial position. Optimally suited for powders in 1-20 mg range,...
Read More »
Portable Wire Feeder includes Soft Start(TM) run-in control.
Voltage-sensing SuitCase(TM) X-TREME(TM) 12VS holds wire spools up to 12 in. and features SunVision(TM) digital meters that display voltage and wire feed speed or amperage, and are visible in direct sunlight. Two drive rolls provide positive feeding with solid wires from .023-5/64 in. and cored wires from .030-5/64 in. Featuring polypropylene case, feeder operates on arc voltages from 14-48 Vdc...
Read More »
Gravimetric Feeder handles plastic pellets and regrind.
Consisting of 1-8 feeders and central microprocessor-based controller, ProRate(TM)/Gravimetric Feeder continuously meters raw materials into central station hopper. Each feeder operates in independent, continuous loss-in-weight scaling mode to insure accuracy of each ingredient. Controller monitors weight signals of each feeder and adjusts auger speed to match recipe feed rate. Unit controls 1-8...
Read More »
Bar Feeder handles various sizes and shapes of bar stock.
By changing feed tube size, RHINOBAR can be customized for virtually any size bar stock. Tube sizes range from Ã-¼-2Ã-¾ in. in 1/8 in. increments, accommodating bar stock diameters from 1/8-2Ã-¾ in., and up to 12 ft long. Pedestal and barrel clamps provide stability, preventing whip or spin of bar. Oil fills gap between bar stock and feed tube, acting as noise damping support....
Read More »
Bar Feeder utilizes hydrodynamic forces for operation.
Mini-Rhinobar single-tube bar feeder is engineered for Swiss type CNC screw machines and small, fixed-head CNC lathes. Oil fills gap between bar stock and feed tube, acting as noise damping support. Oil flow and pressure are controlled with single valve, which also allows for accurate bar control and minimizes vibration. Mini-Rhinobar can be controlled from remote pendant for safe operation. Feed...
Read More »
Increase Workplace Safety, Manage Heavy Loads with Equipment from A-Plus Warehouse
A-Plus Warehouse carries a wide selection of commercial and industrial material handling equipment at affordable prices. Check out the video to learn more.
Read More »
