Hand Held Drills

Knockout Punch Driver cuts up to 2 in. conduit holes.
Hand Held Drills

Knockout Punch Driver cuts up to 2 in. conduit holes.

Powered by 18 V Li-Ion battery, Model LS60L can punch hole for 2 in. conduit in 10-gauge mild steel and 12-gauge stainless steel in about 10 sec. Tool senses when hole is completely punched and automatically shuts off to prevent damage to punch and die. Forward handle position optimizes tool balance, and one trigger controls all tool functions. To illuminate dark areas, driver includes LED work...

Read More »
Cordless No-Hub Coupling Driver can fasten up to 300 clamps on single charge.
Hand Held Drills

Cordless No-Hub Coupling Driver can fasten up to 300 clamps on single charge.

Featuring specific torque settings for 60 and 80 lb-in., Lithium-Ion battery powered M12(TM) cordless no-hub driver model 2455-22 is accurate for up to 25,000 clamps before re-calibration. Auto shut-off with LED indicator alerts user when torque limit has been achieved, while LED Calibration indicator alerts user when calibration is needed. Weighing 2.75 lb, driver is 7.5 in. long and features...

Read More »
Drill/Driver also provides impact fastening.
Hand Held Drills

Drill/Driver also provides impact fastening.

Featuring 2-speed 0-750/2,800 rpm motor, 18 V Model 26618-01 offers choice between high speed for small diameter drilling and high torque/low speed for drilling with spade bits or precision driving applications. Tool delivers up to 1,500 lb-in. torque when switched to impact mode. Powered by 18 V Litheon battery platform, drill/driver includes Electronic Motor Protection and Electronic Cell...

Read More »
Portable Pneumatic Drilling Units target aerospace industry.
Hand Held Drills

Portable Pneumatic Drilling Units target aerospace industry.

Designed to streamline drilling applications on large wing and fuselage assemblies, portable air powered Pneucon Selfeeders provide TIR of less than .0006 in. and deliver .0008 in. repeatability on depths. Double Hydro-Speed Regulator technology produces fine holes without burrs, and unit is equipped to provide cutting oil directly to tool tip where lubrication is most needed. Nose-mounted unit...

Read More »
Festool USA Announces the Launch of Three New Products
Hand Held Drills

Festool USA Announces the Launch of Three New Products

Lebanon, In, October 13, 2009 - Festool USA announces three new products available now, including T 12+3 and T 15+3 Cordless drill/drivers (non-set versions), hand sanding blocks, and Systainer SYS 2 Attic. These products highlight the beauty of the Festool system," says Rick Bush, Festool Product Manager. Bush continues, "For those who already have our drills or are just starting, the T + 3...

Read More »
Hammer Drill/Driver suits space-restricted applications.
Hand Held Drills

Hammer Drill/Driver suits space-restricted applications.

Cordless SB18 LT measures 8 13/16 in. long and features chuck that can be removed to drive screws with Â-¼ in. hexagon recessed spindle using accessory bit retainer. Powered by Li-Power Plus 18 V, 2.6 Ah battery, this 5.3 lb tool has aluminum die cast gear housing, Variospeed full-wave electronic speed control, and dual-range torque adjustment. Drilling capacity, with ½ in. chuck, is...

Read More »
Portable Drill/Driver suits rugged applications.
Hand Held Drills

Portable Drill/Driver suits rugged applications.

Part of PowerMasterSeries, cordless BS18 LT is fitted with Li-Power Plus 18 V, 2.6 Ah battery and features air-cooled charging technology. Tool weighs 4.5 lb, measures 8 in. long, and incorporates LED worklight. User can remove chuck to drive screws with Â-¼ in. hexagon recessed spindle using accessory bit retainer, allowing use in tight spaces. Along with Variospeed full-wave electronic...

Read More »
Right Angle Drill/Driver includes spindle lock chuck.
Hand Held Drills

Right Angle Drill/Driver includes spindle lock chuck.

Operating with Li-Ion battery, model 2415-21 M12(TM) Cordless 3/8 in. Right Angle Drill Driver features 3.75 in. head size and 3/8 in. single sleeve ratcheting chuck for maximum control in tight spaces. Unit weighs 2.43 lb and incorporates electronic clutch, fuel gauge, and speed control. Built in overload protection is also included and device has 100 lb-in. torque, 0-800 rpm, as well as 11+...

Read More »
Automatic Drill is solution for odd-shaped beam drilling.
Hand Held Drills

Automatic Drill is solution for odd-shaped beam drilling.

Intended for medium-volume and irregular-shaped beam drilling, Atra Ace lets fabricators drill holes in steel for applications not suited by CNC beam drill line. Operators can bring drill to beam, eliminating material handling efforts, and 2 or more Atra Ace Automatics can be used simultaneously by one operator. There are 5 models, capable of producing holes up to 2 9/16 in. dia and offering...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers