Embedded Computer Module consumes less than 10 W of power.
Build around IntelÃ-® CeleronÃ-® processors up to 1 GHz, Computer-On-Module models ETX-P3T and ETX-P3Tx integrate 10/100 Base-T Ethernet, AC97 Audio Codec, 512 MB SDRAM SO-DIMM memory, and 32 MB dedicated graphics memory. Harsh environment model ETX-P3T uses i815E chipset and offers USB 2.0. Using Intel Northbridge and Southbridge chipsets, ETX-P3Tx is suited for graphics- and...
Read More »
Ethernet I/O Modules speak directly to each another.
Featuring i2o(TM) technology, BusWorksÃ-® 900EN input modules can send measured signal data directly to output modules without PLC, PC, or other controller in between. Analog input modules measure current, voltage, or temperature signals and transmit data to analog output modules that provide proportional 4-20 mA or 0-10 V DC output. Discrete I/O modules control local devices based on level...
Read More »Wi-Fi SiP Module is suited for small mobile phones.
Measuring 9.6 x 9.6 x 1.6 mm, 802.11 b/g Wi-Fi System in Package (SiP) module provides data-sharing solution for VoIP and dual-mode mobile telephony applications. Tailor-made for mobile phone systems and user interface, product eliminates duplicated functions between system and Wi-Fi module to allow for miniaturization of design. No special manufacturing process is required to achieve...
Read More »
Microcontrollers feature 8 MHz internal oscillator.
Flash 8-bit PIC16F685/687/689/690 offer code-compatible migration path from existing 8- and 14-pin package options to 20-pin microcontrollers. Units feature steering-capable capture/compare/PWM module and synchronous serial port with address-masking for I2C(TM). Offered in packages as small as 4x4 QFN, microcontrollers utilize nanoWatt Technology and include comparator module, software-enabled...
Read More »
Hot Forging Process
Check out this white paper to learn about the benefits of hot forging.
Read More »Starter Kit aids in MCU development and programming.
To facilitate development of and experimentation with PICÃ-® microcontrollers, PICkit(TM) 2 Starter Kit connects to PC via full-speed USB 2.0 and allows for firmware upgradeability. It requires no additional power supply for programmer or target application board, and included set of tutorials lets users learn at their own pace. Form factor requires minimal workbench space and can plug into...
Read More »
I/O Module features configuration flexibility.
ArmorBlock 16-point, 24 V dc I/O block features direct connection of On-Machine I/O systems to sensors and actuators using plug-and-play connectors, increasing density of I/O points. Module can be configured for any combination of I/O and suits applications where embedding control technology is not needed. Sealed housing is IP67 and NEMA 4x rated, eliminating need for protective enclosure.
Read More »
CAN Interface Module controls in-vehicle DAQ.
NI 9853 2-port, high-speed Controller Area Network (CAN) interface module plugs into CompactRIO chassis to monitor in-vehicle CAN buses, read and write ECU and actuator values, and communicate with motion drives and motors. CompactRIO and NI 9853 CAN module combine with Labview for 40 MHz CAN data response. Offers 25 nsec resolution data synchronization, with 11-bit and 29-bit arbitration ID...
Read More »
USB DAQ Devices provide sampling rates up to 800 kS/s.
With bus-powered, plug-and-play connectivity, Series USB-9000 includes 4- and 8-channel models with 250 Vrms channel-to-earth ground isolation, noise immunity, and high-common-mode voltage range. Interactive data-logging software enables user to log data and export it to spreadsheet applications such as Microsoft Excel. Utilizing DAQ devices with NI-DAQmx driver software, engineers can develop...
Read More »
Microcontrollers are equipped with analog peripherals.
Incorporating up to 2 comparators and one 8-bit ADC, Baseline 8-bit Flash PICÃ-® microcontrollers PIC12F510 and PIC16F506 are produced in respective 8- and 14-pin packages. Analog features, combined with 8 MHz internal oscillator with 33 instructions and 2 stack levels, facilitate integration of digital intelligence into applications. Along with 1.125 ms DRT, products feature 1,024...
Read More »
PMC Card suits VME, CompactPCI, and PCI systems.
Dual-channel AtlasPMC/1D is based on RADEON Mobility 9000 mobile graphics processor, which supports dual 2D, 3D, OpenGL, and DirectX compatible displays with up to 16.7 million colors. Processor includes 64 MB integrated memory, integrated video output, and quad-pipeline 2D/3D acceleration. AtlasPMC/1D displays analog VGA screen resolution up to 1,920 x 1,200, and can be configured to output DVI...
Read More »
How SpinSelect Can Save You Time and Money
Thanks to the unique SpinSelect™ Multi-Pocket selectable quick change tool holder, it's time to rethink the range, complexity and volume of parts that your lathe can produce. Our Spin-Select™ tool was created to increase productivity and consistency by decreasing downtime associated with lathe cutting tool and insert setups or changeovers. This product is a game-changer for the industry and we're pleased to show you why.
Read More »
