Brush Tips apply materials consistently.
Dispensers

Brush Tips apply materials consistently.

Dispensing Brush Tips, in soft and hard styles, are suitable for applying consistent brush deposits of most materials, particularly grease and lubricants. Tapered bristles ensure accurate applications and long life. Both styles are connected to syringe or dispensing valve by a quick-release Luer-Lock fastening. They can be used with any of company's automatic or manual dispense systems.

Read More »
Pressure Washers are electrically heated.
Washing Equipment

Pressure Washers are electrically heated.

EH Series stationary, belt-driven presssure washers blast away dirt, oil, and grease from engines, equipment, and concrete. On-demand heat exchanger creates continous hot water. Units include adjustable thermostat, low inlet pressure shutoff, low inlet water volume shutoff, diagnostic control panel, and 50 ft high pressure hose. Trigger gun control offers automatic on/off. Single lance wand has...

Read More »
Floor Scrubber offers 56 in. turning radius.
Scrubbers

Floor Scrubber offers 56 in. turning radius.

Encore R rider floor scrubber features 45 gal solution and recovery tanks, and is available with 34 or 38 in. scrub path. It includes auto squeegee lift in reverse, solution and brushes off in neutral, battery discharge brush shutoff, edge cleaning, non-marking tires, and corner roller bumpers. Encore R is suitable for use in manufacturing plants, warehouses, and facility maintenance jobs.

Read More »
Carpet Cleaning System extends carpet life.
Cleaning Equipment

Carpet Cleaning System extends carpet life.

Wash & Rinse(TM) extraction system puts down soapy water, scrubs carpet with cylindrical brush, and rinses carpet with clean water, removing both soap and dirt. System is available on Image 26B and 26E models, and is suitable for high traffic areas or in situations where carpets re-soil faster after being cleaned due to residual soap being left in.

Read More »
Grinder Brushes are suitable for confined areas.
Applicator / Finishing / Cleaning Brushes

Grinder Brushes are suitable for confined areas.

Available in knotted and crimped wire, Mini-Grinder Cup Brushes are offered in carbon and stainless wire and are adaptable to both light- and heavy-duty brushing applications. Crimped wire Mini-Grinder suits applications where uniformed cleaning is required, as well as for flat brushing and edge cleaning. Knotted wire Mini-Grinder suits weld cleaning, scale removal, and deburring. Mini-Grinder...

Read More »
Pressure Washers are available with Robin engines.
Washing Equipment

Pressure Washers are available with Robin engines.

Direct drive Job Pro(TM) cold water pressure washers, suitable for commercial pressure washer applications, are offered with 6.0, 7.0, or 9.0 HP engines. They have low oil protection; 2400, 2700 or 3000 PSI ratings; powder coated steel handles and base plates; and hose wrap with gun/wand holder. Other features include pneumatic tires with tubes, rubber isolators, insulated trigger gun, and 36 in....

Read More »
Wands

UV Wand cures adhesives on the spot.

ZETA(R) 7740 UV Cure Wand System for spot curing applications has stable light output up to 10 W/cm2, providing fast cure cycles and tack-free surfaces. It has high-pressure mercury arc lamp with universal power supply and liquid filled light wand. Exposure time can be controlled using either manual mode, where shutter remains open as long as foot switch is depressed, or timed mode from 0 to 99.9...

Read More »
Brushes prepare surfaces for finishing.
Brushes

Brushes prepare surfaces for finishing.

Fiberglass brushes roughen surfaces to enhance adhesion of solder, paint, and epoxy. Other uses include cleaning electrical contacts, removing rust, removing epoxy and paint, and cleaning injection molds and foil stamping dies. Brushes are suitable for use in printed circuit board industry for PC board rework, including flux removal, edge connector cleaning, trace cleaning for soldering, and...

Read More »
Aqueous Washers suit various applications.
Washing Equipment

Aqueous Washers suit various applications.

VersaForce(i) conveyorized parts washer with immersion cleans with no operator intervention and is suitable for cellular parts manufacturing applications. AquaCell offers in-process cleaning, one person operation, and self-contained design. Recirculating spray wash and air blowoff stages are standard. RTW parts washer has rotating basket below submergence and handles gross amounts of oils and...

Read More »
Tekna Manufacturing LLC Announces NFPA 99 Compliant Model 7200 Multiplace Chamber
Sponsored

Tekna Manufacturing LLC Announces NFPA 99 Compliant Model 7200 Multiplace Chamber

Tekna is a leader in Monoplace and Multiplace Hyperbaric Chambers for Hyperbaric Oxygen Therapy (HBOT), offering products that set the standard for quality and innovation. Our new 7200 series of multiplace chambers is a state-of-the-art system that integrates advanced engineering with a plethora of features and options making it the industry's premier HBOT system. To learn more, see our video.

Read More »

All Topics