Epoxy Meets Airbus Standards for Flame Retardancy, Smoke and Gas Emissions
Formulated to meet rigorous Airbus specifications, Master Bond EP93FRHT passes the twelve second vertical burn test per AITM 2.0002B and Section 7.1.2 of ABD0031, Issue F; the smoke emission test per AITM 2.0007B, Issue 3 in the flaming mode and Section 7.3.2 of ABD0031, Issue F; and the toxic gas emission test per AITM 3.0005, Issue 2 in the flaming mode and Section 7.4 of ABD0031, Issue F....
Read More »
70-3812NC Epoxy Adhesive meets ASTM E-595-07 standards.
Providing enhanced bonding and thermal conductivity, 70-3812NC Aluminum Filled Epoxy Adhesive is suitable for bonded fin heat sink and pipe bonding in extruded aluminum base applications. Formulated to be cured at room temperature or with mild heat, product’s 10:1 mix ratio is easy for batch mixing or using Meter Mix and Dispense Equipment.
Read More »
Uni-Seal™ 6322: UV / LED / Visible Hybrid Low Shrinkage (Soft) Gasketing Sealant / Bonder
Incure Uni-Seal™ 6322 UV / Visible / LED light curable adhesive is an acid-free, low viscosity form-in-place / cure-in-place gasket (FIPG / CIPG). Cures very fast with low energy LED lamps for high volume production. High resilient (good memory retention) and high flexibility out-perform many gaskets provides air-tight sealing. Uni-Seal™ 6322 exhibits enhanced excellent moisture and...
Read More »
SCProbond™ Adhesives are non-corrosive epoxy system.
Formulated to adhere ceramic components in material handling, power generation, mining and petroleum industries, SCProbond™ Epoxy Adhesives are available in low (LV-1) and high viscosity (HV-1) versions. SCProbond™ LV-1 is used in installing components in horizontal applications whereas SCProbond™ HV-1 is designed for vertical and overhead tilting applications. Product features good...
Read More »
A Quick Guide to MASKING SOLUTIONS
This guide will provide an overview of the different masking options, and provide insight on which to use for your product.
Read More »
Needle Bonding Adhesive enhances performance on smaller cannulas.
Suitable for small gauge needle applications, MD® 1406-M Needle Bonding Adhesive reduces chance of cannula substrate failure. Allowing tighter standard deviations, product is optimized for 385 nm LED curing. Product helps manufacturers with use of LED curing without affecting speed and cured mechanical properties.
Read More »
Adhesives for Your Specific Need
EP41S-5: Chemical Resistant Epoxy Withstands Methylene Chloride EP41S-5 has exemplary resistance to a wide array of chemicals, such as acids, bases, alcohols, fuels and many solvents. This two part epoxy is widely used for bonding, sealing and coating, as well as encapsulating. This system combines formidable physical strength properties and electrical insulation values. EP41S-5 offers convenient...
Read More »BP 256 Ball Attach Adhesive
(Albany, NY) January 13, 2017 - BP 256 is YINCAE’s new ball attach adhesive product. BP 256 has been designed to enhance solder joint reliability and eliminate cleaning processes for LEAD-FREE ball bumping procedures on CSP, BGA, Flip chip, and PoP devices. It is compatible with current ball bumping processes. BP 256 is generally applied via printing or pin transfer methods and can replace...
Read More »
Light-Curable Adhesives Formulated with Encompass™ Technology to be Showcased at MD&M West
Torrington, Connecticut - January 16, 2017 - Dymax Corporation, a leading manufacturer of adhesives to the disposable medical device industry, will exhibit in Booth #2139 at MD&M West, scheduled to take place February 7-9, 2017 at the Anaheim Convention Center in Anaheim, CA. Their newest products and technologies - including solvent free, USP Class VI, and ISO 10993 biocompatible...
Read More »
One Component Elastomeric System Features Excellent Thermal Conductivity
Master Bond X5TC is an elastomeric system that has a thermal conductivity of 10-12 BTU•in/ft2•hr•°F [1.44-1.73 W/m•K] while maintaining solid electrical insulation properties. This one part, no mix adhesive/sealant has a paste-like consistency and is very easy to use. It readily cures in 8-12 hours at room temperature or in 60-90 minutes at 150°F. X5TC bonds well to many substrates...
Read More »
Plexus Galvanized Bonder Adhesives for bonding hot-dip G60, G90.
Used to bond dissimilar substrates without requiring primers, Plexus Galvanized Bonder Adhesives cure instantly at room temperature. After curing, adhesives are strong and tough with resistance to sheer, peel and impact. Materials doesnot require external fasteners once cured. Product bonds galvanized metals like G60 and G90, plastics, composites, steel and aluminum.
Read More »
SRG Global Coatings Enhance Surface Durability, Efficiency, Design Flexibility
SRG Global's automotive coatings enhance the structural integrity of the finished part while also improving vehicle efficiency. Check out our video to learn more.
Read More »
