Sokymat SA
Granges CHE
Share:
Compound is used for underfill and encapsulating applications.
TRA-CAST 3108 two part epoxy casting paste works on wide range of surfaces, including glass, ceramics, metals, plastics, and many electronic materials. It is all-liquid, low viscosity product with good flow and wetting characteristics. Casting compound can be cured at room temperature with little or no shrinkage, and it resists all weather conditions, gases, galvanic action, petroleum fuels,...
Read More »
Valve Controller Trio satisfies various requirements.
IN-Series interface units include three controllers: IN-23 Y 3 Proportiontal Controller uses control action that progressively closes valve. IN-VCC valve current controller interfaces between process loops and control valves; it accepts 4-20mA control signal and uses this to regulate current applied to valve. Phasecut controls Staefa valves. It modulates valve using 0-20V phase-chopped output...
Read More »
Drum Motor Drives drive food conveyors.
Internally powered drum motors are available with USDA Dairy 304 or 316 stainless steel shell, shafts and end flanges that resist corrosion and contamination prohibited in food industry. Each motor is filled with food grade oil and hermetically sealed, making it suitable for applications requiring daily high-pressure washdown and acid or alkaline power washings. Drives have sprockets for driving...
Read More »
Porometer determines volume without using mercury.
Capillary Saturation Porometer determines pore volume and measures liquid permeability. For volume, sample is soaked in liquid that spontaneously fills pores. Pressure of non-reacting gas on top of sample is increased to displace liquid from pores, and pore volume, diameter, and volume distribution can be computed. To measure liquid permeability, pressure is increased, and permeability is...
Read More »
Portable Batch Sifter is suitable for food and pharmaceutical.
Lightweight batch version of Flo-Thru Vibroscreen separator scalps oversize particles from small batches of bulk material being loaded into drums, blenders, process equipment and storage vessels. Sifter is available in 18, 24 and 30 in. dia. with imbalanced-weight gyratory motor. All are made of stainless steel and finished for industrial, food, dairy or pharmaceutical applications....
Read More »
Color Coder prints two lines at a time.
Twin Convertible Slimline Coder mounts two printing units on single mounting shaft running next to each other, offering flexibility in marking and coding products. It can print multiple lines in different colors, different fonts sizes, and in different locations on same carton. Color cartridges can be changed quickly. Coder can be mounted to any conveyor, cartoner, case sealer or processing...
Read More »
Adjustable Screwdriver eliminates overtorquing.
Adjustable torque manual screwdriver lets operator dial in torques from 20 oz-in to 40 ft-lb. via twist action. Slip clutch prevents over-torquing, and driver automatically resets for next fastener after torque is reached. 3 models are available: 20-100 oz-in, 3-15 ft-lb, and 5-40 ft-lb. Preset manual torque drivers are also available. All manual drivers are calibrated to meet/exceed accuracy and...
Read More »
End Stops reduce noise and excessive wear.
Cushioned End Stops are neoprene spacers that match ID/OD dimensions of shaft collars to reduce problems caused by metal-to-metal contact in linear stroke applications. PTFE version provides low coefficient of friction in rotary applications, and help prevent galling from stainless steel contacting stainless steel. End stops come in sizes from 1/2 ID x 1-1/8 in. OD up to 2 ID x 3 in. OD. Neoprene...
Read More »
Mini Flap Discs work with small air grinders.
POLIFAN(R) flap discs are available in sizes of 2 and 3 in. dia., in flat and conical styles, and in zirconia grain with grit range 24 through 120. Discs are able to grind and finish in one step, and stay aggressive throughout life of disc. Flap discs do not require backing, run cooler, and are suitable for use on all materials.
Read More »
Etching Process produces high-precision metal parts.
AccuCoil PCM process combines photochemical machining for producing precision burr-free and stress-free metal parts with accurate frame-to-frame indexing on coil stock. It produces intricate and close tolerance patterns in varieties of flat, metal parts with thickness ranges of 0.0005 to 0.062 in. Holes or slots can be as small as 1.2 times material thickness, and spacing between holes or cutouts...
Read More »