Sokymat SA
Granges CHE
Share:
Level Switch uses tuning fork sensor.
LZ10 Tuning Fork Level Switch vibrates at nominal frequency of 400 Hz. As switch becomes immersed in liquid or slurry, corresponding frequency shift occurs. When measured frequency shift reaches setpoint value, switch changes state indicating presence of liquid or solid medium. It is suitable for liquid applications with light to medium coating or scaling-type characteristics, or lightweight...
Read More »Pushbutton Switches provide security in harsh environments.
AV series pushbutton switches are suitable for applications where control panels are in high traffic or unsupervised locations, such as process control panels. Each has metal bezel with low profile shape that prevents attempts to remove switch from front of panel, anti-jamming construction, reduced actuator travel to prevent insertion of foreign parts, and solid mechanical stop inside metal bezel...
Read More »Faceplate Handles are used for CompactPCI equipment.
CP-HP Series Handles are fully compliant to IEEE 1101.10, PICMG 2.16 CompactPCI, VME, and Eurocard specifications. They have dual locating pins which assure horizontal and vertical alignment for wide range of faceplates in applications including electronic enclosures, printed circuit, computer, datacom/telecom, industrial control, security, and test and measurement. Handles are easily mounted...
Read More »
Welding Curtain filters and protects.
Spectra Orange See-Thru Curtain filters welding arc image and all far U.V. radiation and blue light. While transmitting outside light into welding booth to aid welder's vision, curtain also provides safety to surrounding areas. It is suitable for low to high amperages in electric arc welding and may be used for MIG, TIG, ARC, plasma and other high amperage welding arcs. 40 mil curtain provides...
Read More »
Door Lock keeps tight seal on knockout doors.
Posi-Lock bottom seal protects dock area against threats to indoor environment brought about by loss of conditioned air and entry of winds, debris and moisture. When door is shut, lock automatically captures detent pin attached to top door panel. This holds door snugly in place against dock leveler plate. It also has Y-Block that forces top panel firmly to lentil seal, preventing escape of any...
Read More »
Sticky Mat keeps feet clean.
Tacky Mat 800030 has strong adhesive coating that removes dirt on contact to protect sanitary conditions in cleanroom areas. Each mat has 30 disposable sheets. When top sheet becomes soiled, user simply peels it off to expose new, clean surface. Adhesive strips stick to floor to keep mat in place. No frame is required. Mat is made from 2 mil polyethylene sheet and is non-allergenic, non-odorous,...
Read More »
Roll Tester checks gear sets.
Model 600HTT Turbo Tester performs CNC-controlled roll testing of spiral and hypoid bevel gear sets. In addition to basic pattern checking, it provides SFT (single flank transmission error) testing and SBN (structure-borne-noise) testing capabilities for both soft and hard parts. It can accommodate workpiece diameters to 600 mm.
Read More »
Paint Brush works with latex and oil.
The Wave(TM) uses polyester filaments blended with fine natural china bristles. Resulting blend picks up and releases more latex paint per dip than most other brushes. Each brush has hand-trimmed, natural flagged bristles held in place with heavy-duty stainless steel ferrule. Its handle is sealed beechwood. The Wave is available in 8 sizes and 4 different cuts: thin angle sash, angle sash, trim,...
Read More »Lube-free Chain exceeds ANSI specs.
Xceeder Chain has oil-impregnated felt seals that keep dirt out and lubrication in for increased wear life. Drive, conveyor, and attachment chains are available in sizes 40 to 100, are interchangeable with ANSI standard chain, and work with standard sprockets. They handle same maximum loads as ANSI standard chain, and exceed ANSI minimum tensile strength requirements.
Read More »
Tool Software finds, manages and tracks tools.
Version 4.3 of AutoTAS tool management software simplifies purchasing, tool crib and tool room operation, and tool presetting and calibration. Enhancements include search capabilities to help users find tools, improved tool grouping, more user definable fields, and improved ability to monitor tool life and service tooling. Software is arranged in eleven discrete and fully integrated modules that...
Read More »