Aprima Medical Software, Inc

3330 Keller Springs Suite 201
Carrollton, TX 75006

Foot Switches are suitable for hostile environments.

PX and PA series foot-switches are available in single or double switch models as well as in covered and uncovered models. Protective covers on PX models are available in yellow, red, or orange; come with full or half covers; and are constructed of high impact plastic. Available with slow- or snap-action contact elements, foot switches offer various contact block configurations. Both series carry...

Mechanical Components and Assemblies

Test plug provides universal testing option.

Modular spring type test plug may be used to test terminal block current for both taris IDC and fasis spring clamp terminal block styles in 5 mm and 6 mm pitch blocks. Test connection entry point is positioned as a top mount version and each module is individually marked. Manufactured of UL 94 V-0 polyamide 6.6 plastic for flammability resistance, test plug is rated for 2.5 A, 400 V for 26-16 AWG...

Architectural & Civil Engineering Products

Touchscreen upgrades PLCs.

Model GT-10J, with green backlit LCD and 192 KB memory, offers multiple PLC drivers such as Allen Bradley, Aromat, Modbus RTU, Siemens, and Mitsubishi. Programming software supports bitmap graphics, true-type fonts, key switches, multiple message texts, data-entry points, and function keys. Unit can be connected to custom board controller or PC. GT-10J supports modem capability for remote...

Pumps provide slurry metering.

Self-priming Slurry-Duty Metering Series Pumps are available in 3 sizes and provide consistent, pulse-free metered flow at up to 37 gpm and 1200 psi. Able to run dry without damage, their sealless design allows flow to remain linear throughout pressure range. Suited for pumping harsh, abrasive slurries, shear sensitive fluids, and clean, corrosive chemicals, pumps utilize hydraulically balanced...

Controls & Controllers

Voltage Regulator has round-tank functionality.

Pad-mounted, Single-phase, 32-step, voltage regulator allows system planners to regulate voltage on new and existing underground systems. Unit is available for system voltages from 2400 V, 3-wire to 24940 V, 4-wire. With current ratings from 50 to 548 A, regulator incorporates either 200 or 600 A deadfront termination system. Features include CL-5 control, automatic pressure-relief device, and 3...

Adhesives & Sealants

Threadlocker/Sealant replaces lockwashers.

PERMABONDÃ-® HH120 seals fasteners against water and chemicals. It obtains fixture strength in 15-20 min on active metals such as iron, steel, nickel, and aluminum. Viscosity is 7000 cp, allowing for gap filling up to 10 mil. HH120 features locking strength of 250-350 lb-in. and retaining strength of over 2000 psi. It is suitable for locking bolts, nuts, and screws for permanent assembly, and...

Mechanical Components and Assemblies

Gaskets are highly conductive and provide EMI shielding.

Soft GORE-SHIELDÃ-® GS8000 EMI gaskets consist of nickel-plated base polymer, backed with thin foil layer and electrically conductive, pressure-sensitive adhesive. Less than 3.4 N/cm of pressure compresses gaskets from nominal starting thickness of 1 mm to thickness of 0.4 mm. At this point, DC resistance is less than 10 mOhm for a 19 mmÃ-² donut, and shielding effectiveness is greater...

Material Handling & Storage

Chain Conveyors have modular design.

Flat-top and table-top chain conveyors are based on aluminum-profile frames with full length t-slots for assembly components, such as side-frames, drive units, supports, and guide rails. Flat-top chain choices including steel and thermoplastic are available in standard widths of 3Ã-¼, 4, 4Ã-½, 6, 7Ã-½, 10 and 12 in. Conveyor chain choices include all plastic, all steel, and roller...

Gear Motors offer maximum continuous torque to 100 lb-in.

Model M1600 GIL100 PM DC parallel-shaft gear motors are available in 12 to 115 V models. All are UL-approved and feature high-energy ceramic magnets, reversible designs, double-shielded ball bearings on motor, and needle bearings on gearbox. They also include Class F insulation, dynamically balanced armature, TENV design, and auto-hook tang-type commutator. Brushes are externally replaceable.

Controls & Controllers

MIL-STD-1553 Terminal is offered in various configurations.

Mini-ACE Mark3, 3.3 V, fully integrated, MIL-STD-1553 BC/RT/MT terminal uses 0.77 in.Ã-² board space and measures 0.13 in. high. It is offered with RT-only or BC/RT/MT functionality, 4K x 16 or 64K x 17-memory compliment, and either PCI or generic processor backend interface. Mini-ACE Mark3 works with 8, 16, or 32-bit processors with little or no glue logic while PCI Mini-ACE Mark3 series...