Macro Sensors    Pennsauken, NJ 08110 1334
May 16, 2013 Compatible with most LVDT and RVDT linear position sensors, EAZY-CAL LVC 4000 digitally communicates with up to 16 devices simultaneously and can be connected together in master/slave configuration for multiple channel applications. DIN rail-mount unit features digital calibration using 2 pushbutton front panel controls to set zero and full scale. To facilitate LVDT linear position sensor operation in extreme environments, signal conditioners can be remotely located by up to 100+ ft.

PCB Piezotronics Inc.    Depew, NY 14043 2495
Apr 08, 2013 Designed for use with ICP® and traditional charge output sensors, PCB® Models 483C40 and 483C41 also accept direct voltage input and feature selectable low pass filtering. Model 483C40 can be setup and controlled via Ethernet interface, while Model 483C41 has Ethernet interface and front panel keypad and display for setup and control. Multi-Channel Signal Conditioner (MCSC) Control Software comes standard on both multichannel signal conditioners.

PCB Piezotronics Inc.    Depew, NY 14043 2495
Apr 02, 2013 Designed for use with ICP® and traditional charge output sensors, 8-channel Models 483C40 and 483C41 also accept direct voltage input. Model 483C40 can be setup and controlled through Ethernet interface, while Model 483C41 has both Ethernet interface and front panel keypad and display for setup and control. Both are supplied with Multi-Channel Signal Conditioner Control software.

Mini-Circuits    Brooklyn, NY 11235
Apr 02, 2013 Suitable for transmitters/receivers, harmonic rejection, and lab use, 50 Ω Model NBP-1560+ features fast roll-off, which will attenuate frequencies closer to passband with rejection value of greater than 20 dB. Sharp shape factor helps in adjacent rejection, while rugged connectorized package easily interfaces with other devices and is well suited for test set-ups.  

Pulse Electronics    Trevose, PA 19053
Mar 25, 2013 Designed with 6 pins instead of 4 pins, B8841PNL Central Office VDSL2 Splitter Module enables protective device, such as sidactor, to be added on board underneath module and eliminates need for separate protection rack card. Pin location allows fast-acting secondary over-voltage protector to be used to protect filter from surge effects while maintaining VDSL2 performance. Splitter meets requirements for ETSI 600 Ω ADSL to VDSL2 applications and China YD/T 1187-2006 ADSL 600 Ω.

Automation Systems Interconnect Inc.    Mechanicsburg, PA 17055
Mar 25, 2013 Housed in modular DIN rail mount package, X756510 Analog Signal Converter/Isolator covers 0–10 V, 0–20, and 4–20 mA input/output ranges. Multi-function 24–240 Vac/Vdc unit features DIP switch programming, 3-way isolation, and self-calibration circuitry that delivers accuracy without manual adjustment.

Pepperl+Fuchs    Twinsburg, OH 44087
Mar 18, 2013 Featuring 3-port isolation, 12.5 mm SIL-rated KC Series can be programmed and configured in field with pushbutton or dip switch logic functions. Units provide limit detection with form C alarm contacts, as well as fault detection and alarm functionality. With spring terminals, cable is inserted in socket and fixed by spring force, and can be released by pressing terminal button. Devices are suited for control rooms with limited space in both hazardous areas and general purpose locations.

Crestron Electronics, Inc.    Rockleigh, NJ 07647
Mar 05, 2013 Built to meet HD and analog AV distribution requirements for large commercial facilities, 64 x 64 DigitalMedia™ Switcher accepts, manages, and distributes 64 AV sources of virtually any signal type over Cat5e wire or fiber. System features hot-swappable modular blade I/O expansion system, 15 in. color touchscreen, and built-in web server that enables full operation and monitoring through any web browser. Applications include stadiums, arenas, university campuses, and corporate enterprises.

Mini-Circuits    Brooklyn, NY 11235
Feb 20, 2013 Housed in 3.2 x 1.6 mm EIA 1206 package, 50 Ω Model HFCN-103+ integrates 7 high pass sections in SMT chip form factor. Device features ceramic construction, power handling capability of 8 W, and typical stop band rejection of 30 dB. Systems that previously relied on large distributed filter elements to support these lower frequencies can save space and system complexity by integrating HFCN-103+ into designs. 

Northrop Grumman Corp.    Los Angeles, CA 90067-2199
Jan 14, 2013 Designed to protect fixed-wing and rotary military aircraft, All Semiconductor Airborne Laser Threat Terminator (ASALTT™) will house high brightness and high power Quantum Cascade Laser (QCL) module. QCL module will operate at 10 W in MWIR spectrum, enabling real-time color ratio control and diversifying Technology Readiness Level 6 ASALTT laser systems. Modular architecture of these opto-mechanical and environmentally stable systems enables utilization of key subsystems in adjacent markets.

Pentek Inc.    Upper Saddle River, NJ 07458
Dec 14, 2012 Suitable for military/aerospace applications, Talon® Model RTR 2727 offers recording and playback of IF signals up to 700 MHz with signal bandwidths to 200 MHz. It can be configured with 500 MHz, 12-bit ADCs or 400 MHz, 14-bit ADCs and 800 MHz, 16-bit DAC. SystemFlow software enables turnkey operation via GUI, while API fosters integration of recording software into custom applications. Chassis supports up to 8 hot-swap SSDs (3.8 TB max) with RAID 0/1/5/6 as well as several I/O interfaces.

Semrock Inc.    Rochester, NY 14624
Dec 13, 2012 Intended for fluorescence imaging and metrology applications, EdgeBasic™ Long Pass-Edge Filters combine steep edge locations from 325–1319 nm, extended blocking at and below laser line, and consistent and extended high transmission pass bands. Featuring hard coated, no burn-out durability, filters are suitable for application-specific Raman spectroscopy when optimized laser-line blocking is required and Raman shift measurement is not too small.

WAGO Corp.    Germantown, WI 53022
Nov 30, 2012 Model 857-500 JUMPFLEX® Frequency Signal Conditioners convert frequencies from NPN or PNP sensors, NAMUR sensors, dry contact switching, or pulse generator signals to analog signals. Converting 0–5 A, AC or DC current measurement to analog signal, 857-550 JUMPFLEX® Current Signal Conditioner supports arithmetic mean value, true RMS, signal mapping, or absolute measurements. Both 6 mm DIN-rail mount units have 2.5 kV 3-way isolation and -25 to +70°C operating temperature range. 

Alliance Sensors Group    Moorestown, NJ 08057
Nov 27, 2012 Engineered to work with AC-LVDTs, RVDTs, and inductive half-bridge sensors, S1A DIN rail module supports LVDT operation and indicates most common failures. Built-in null indication and front panel pushbuttons, used to set zero and full scale, accelerate intelligent LVDT setup, while internal MPU eliminates need to calculate jumper connections for gain, range, etc. Conditioner offers choice of 4 excitation frequencies, 8 analog DC outputs, and RS-485 digital communications.

Pentek Inc.    Upper Saddle River, NJ 07458
Nov 26, 2012 Onyx Model 71720 3-channel, 200 MHz A/D, 2-channel 800 MHz D/A module features 4 GB, 1,600 MHz DDR3 memory and PCIe Gen 3 interface with peak transfer rates up to 8 GB/sec. Included GateXpress™ FPGA-PCIe hardware engine facilitates managing reconfiguration of FPGA through software commands. Designed for air- and conduction-cooled systems, module also includes functions for data capture, synchronization, time tagging, and formatting in radar, communications, or DAQ applications.

M/A-COM Technology Solutions, Inc.    Lowell, MA 01851
Nov 21, 2012 Supplied in 4 mm, 24-lead PQFN package, MAPS-011008 GaAs pHEMT phase shifter suits C-Band Radar applications from 5.0–6.0 GHz. Product is controlled with single +5.0 V serial or parallel control line and provides 360° phase shift range with step size of 5.6°. Insertion loss is 4.0 dB, with ±0.5 dB attenuation variation and ±3.0° phase accuracy over 5.0–6.0 GHz range. Other features include 0.3 dB RMS attenuation error and 2° RMS phase error.

Acromag, Inc.    Wixom, MI 48393 7037
Nov 20, 2012 Comprised of isolated signal conditioners, TT330 series supports high-density mounting on DIN rails and provides USB connection to PC for configuration using Windows® software. Several models are available to convert thermocouple, voltage, or current input signal types to choice of bipolar or unipolar ranges for proportional voltage or current output signals. Process signal converters are DC-powered (12–32 V) and support bussed rail power option for primary or redundant power.

Pentek Inc.    Upper Saddle River, NJ 07458
Nov 13, 2012 Supplied in conduction-cooled ½ ATR chassis with up to 1.92 TB solid-state RAID storage, configurable Extreme Talon® Model RTX 2786 digitizes and records multiple analog input channels using 200 MHz, 16-bit ADCs. Recording and playback system, which supports remote control, can capture up to 80 MHz of instantaneous bandwidth for IF signals ranging up to 700 MHz. Unit supports recording rates to 500 MBps from up to 4 data channels and also incorporates digital downconverters.

Acromag, Inc.    Wixom, MI 48393 7037
Oct 04, 2012 At 12.5 mm wide, signal conditioners comprising TT230 series, suitable for high-density mounting on DIN rails, includes models to isolate and convert thermocouple, RTD, voltage, or current input signals to 4–20 mA output. Each model accommodates various signal types, and USB connection to PC aids configuration using Windows® software. These loop-powered instruments support both source or sink output wiring connections on current loop with 12–32 Vdc supply.

Edmund Optics    Barrington, NJ 08007
Sep 28, 2012 Suited for Raman spectroscopy or Life Sciences instrumentation, TECHSPEC® Raman Longpass Edge Filters create sharp transition between transmitted Raman signals and blocked laser wavelengths. Single-filter solution, used for reducing spectral noise in Stokes shift applications, have hard coated design. Providing deep blocking for maximum laser rejection, filters come in 325, 355, 473, 488, 514.5, 532, 632.8, 785, 980, and 1,064 nm cutoff-wavelengths in both 12.5 and 25 mm dia.