Henkel Loctite Corporation
Rocky Hill, CT 06067
Mar 13, 2007 Pre-applied to board at corners of CSP pad site using standard dispensing system, one-component Loctite® Cornerbond(TM) 3508 cures during normal lead-free solder reflow, allowing for self-alignment of IC components. It provides 6-month shelf life, pot life greater than 75 hr, and ability to use standard refrigerated storage. Reworkable feature enables defective components to be removed without requiring entire assembly to be scrapped.

Epoxies Etc.
Cranston, RI 02921-3407
Mar 12, 2007 Electronics-grade UV-curable adhesive and potting compound, UV Cure 60-7108, adheres to most substrates and exhibits favorable exterior durability. It self levels in and around electronic components and is formulated to maintain its clarity over time. Suitable uses include fiber optics or other optical bonding applications.

Pres-On Products, Inc.
Addison, IL 60101
Mar 09, 2007 SG6400 Series Structural Glazing Tape is coated on both sides with acrylic adhesive that bonds instantly with fabrication materials such as vinyl, plastics, powder paints, bare metal, and glass. With rugged construction, high-strength open cell urethane foam tape resists fungi and oxidation to preserve performance and appearance of building structures. It is available in 1/8, ¼, or 3/8 in. thicknesses on rolls up to 50 ft long.

Adchem Corp.
Riverhead, NY 11901
Mar 08, 2007 Featuring pressure sensitive acrylic adhesive, fiber-filled Models 7742-74 and 7745-74 are 2 mils and 5 mils, respectively. Both provide optimal shear strength at elevated temperatures up to 300°F, and offer bond strength sufficient for splicing metal coils. Polyester fiber reinforcement provides roll stability when slit to widths as narrow as in 1/8 in. Tapes resist thermal cycling, salt solution, acid, brake fluid, and UV environments.

Huntsman Advanced Materials
Los Angeles, CA 90039-1011
Mar 08, 2007 Featuring chemical and moisture resistance, ARALDITE® Epoxy Adhesives are suitable for bonding and potting electronic components. Room temperature- and elevated temperature-curing products are RoHS-compliant and sag resistant. Providing lap shear strength, high-temperature ARALDITE® Polyurethane Adhesives can bond hard-to-join thermoplastic substrates and encapsulate pressure-sensitive components. All come in dual-barrel cartridges as well as bulk packaging for automated mixing/dispensing.

Master Bond, Inc.
Hackensack, NJ 07601
Mar 02, 2007 With service temperature range of -60°F to over 400°F, Type EP30HT epoxy produces high strength, rigid, chemical resistant bonds, and adheres to similar and dissimilar materials such as metals, glass, ceramics, wood, vulcanized rubbers, and plastics. Product attains shear bond strengths over 3,200 psi, with volume resistivity greater than 1,015 W-cm, dielectric strength of 440 V/mil, and dielectric constant of 3.46 at 1 MHz.

APM-Hexseal Corp.
Englewood, NJ 07631
Mar 01, 2007 Used with company's re-usable, high-pressure, self-sealing screws, bolts, and nuts, mechanical and liquid-applied threadlockers are fully adjustable Nylon locking pellets and strips that can be added to thread surface and precisely positioned to optimize anti-vibration dampening. Devices remain locked, whether fastener is seated or unseated, and are impervious to chemicals/water/motor fluids. Reusable to +550ºF, products do not dry, shrink, or loose resiliency upon chemical exposure.

National Starch & Chemical Co.
Bridgewater, NJ 08807-0500
Feb 28, 2007 Balancing tack, open time, and set speed while minimizing moisture transfer into sheet, Ultimate Control(TM) 32-541A resin adhesive helps laminators attain optimal line speeds. Hold-out properties let operators meter glue-line width, reducing waste adhesive drip from flute tips. Glue line thickness can be metered down, and adhesion and set time can be controlled. Product runs effectively on heavy, coated, or varnished sheets as well as on lighter, uncoated sheets without slinging.

National Starch & Chemical Co.
Bridgewater, NJ 08807-0500
Feb 28, 2007 Used for making rolled goods for metal buildings industry, Bondmaster® 40-453A is formulated copolymer emulsion adhesive that bonds foil, scrim, kraft, and other facings to fiberglass insulation. Able to be roll coated, extruded, or air sprayed, this 54% solids adhesive has 800 cps viscosity and formulation that promotes wet tack and product life expectancy. Tack reduces slippage of poly or foil facings when bonded to fiberglass.

National Starch & Chemical Co.
Bridgewater, NJ 08807-0500
Feb 28, 2007 DURO-TAK(R) acrylic solution pressure sensitive adhesive is designed to enable dispersed drug patch formulations. Supplied in non-polar cyclohexane solvent, it is targeted at specific drugs that have low solubility in non-polar solvents, and simplifies preparation of dispersed drug-in-adhesive patches by reducing potential for supersaturation.

National Starch & Chemical Co.
Bridgewater, NJ 08807-0500
Feb 28, 2007 Providing high level of drug solubility for hydrophilic drugs such as nitroglycerin, DURO-TAK® 87-202A is supplied in organic solvent solution. Self-curing, pressure-sensitive adhesive also offer high moisture vapor transmission rate, which contributes to long wear times, especially when used with non-occlusive or semi-occlusive backings.

Aremco Products, Inc.
Valley Cottage, NY 10989
Feb 23, 2007 Single-part, zirconia-filled Ultra-Temp(TM) 516 demonstrates dielectric strength of 250 V/mil, volume resistivity of 108 W-cm, and torque strength of 8.6 lb-in. Due to its inert chemistry, product will not outgas under ultra high vacuum. It also provides chemical, moisture, and thermal shock resistance. Applied with syringe, brush, or automatic dispenser, water-based adhesive achieves full cure by heating up to 700°F for 1-2 hr.

Deposition Sciences, Inc.
Santa Rosa, CA 95403
Feb 19, 2007 Suited for applications in general lighting, medical systems, digital imaging, LED lighting systems, and portable optical systems, HeatBuster® Spectral Metal Thin Film Coating meets severe abrasion, adhesion, humidity, and salt fog tests of Mil-C-675 standards. Stable over temperature and humidity changes, dichroic hybrid coating operates over range of angles, and is designed to be highly reflective over selected bands of wavelengths and minimally reflective over rest of the spectrum.

Master Bond, Inc.
Hackensack, NJ 07601
Feb 09, 2007 Suitable for use in both thick/thin sectioned configurations, EP21TDC-2LO bonding, sealing, coating, and encapsulation system has thermal conductivity of 9 BTU/in./ft²/hr/°F and volume resistivity of 1,012 Wcm. With service operating temperature range of 4 K to 250°F, room temperature curable product features Shore D hardness of 36, elongation of 50%, 1:3 mix ratio by weight or volume, working life of 90 min for 100 g mass, tensile strength of 1,070 psi, and T-peel strength of 15 pli.

Excel Scientific Inc
Wrightwood, CA 92397
Feb 05, 2007 Sized to fit within edges of raised-rim 96-well plates, 50 µm ThermalSeal RT2RR(TM) features inert, temperature-resistant adhesive that ensures reliable sealing around each well. Two end tabs assist in positioning film, while removal of end tabs at perforated boundaries prevents lifting and minimizes evaporation rates. Product is suitable for specific DNA sequence detection in clinical diagnostics, forensic science, and basic research.

Master Bond, Inc.
Hackensack, NJ 07601
Jan 31, 2007 Suited for sealing and joining of metals, plastics, electrical insulations, protective coatings, and formed-in-place gaskets, Master Sil 700 silicone elastomer compound has dielectric strength of 530 V/mil and 400% elongation. Silicone adhesive/sealant features paste consistency and does not sag, slump, or run off surfaces. It cures at ambient temperatures to a flexible rubbery solid when exposed to atmospheric moisture and remains flexible over temperature range of -75 to 400°F.

Lord Corporation
Cary, NC 27511
Jan 30, 2007 With LORD Accelerator 19GB Gray mix-in curative, LORD 400 Series Acrylic Adhesive will bond variety of prepared or unprepared aluminum materials. Accelerator allows precise control of adhesive bondline thickness due to its content of 0.01 in. dia glass beads. Used for cars, trucks, specialty vehicles, and boats, cured adhesive distributes stress, acts as sealant, helps prevent corrosion, and maintains original mill finish of exterior surface of thin panels.

Aremco Products, Inc.
Valley Cottage, NY 10989
Jan 23, 2007 Pyro-Tape 682-Series tapes are for use in plasma spray masking, heat protection, and abrasion-, chemical-, and electrical-resistance applications. Able to withstand temperatures to 500°F, 682-PM is for plasma spray masking, 682-HR is heat reflective tape for components and pipes, and 682-CR is non-stick and corrosion-resistant. Type 682-DS is double-sided tape, while 682-ER is used for electrical insulation. Used to provide abrasion-resistance, 682-AR functions at up to 200°F.

3M Adhesives & Tapes Div.
St. Paul, MN 55144 1000
Jan 23, 2007 With Adhesive 375, 3M(TM) High Performance Double Coated Tapes provide long-term bond to high and low surface energy substrates, such as painted and unpainted surfaces, stainless steel, glass, polycarbonate, polypropylene, ABS, wood, fabric, and leather. Products offer resistance to UV light, solvents, plasticizers, and high temperatures. Red liner indicates clear tape, while green print liner identifies thickest product in family, and black print liner denotes hand tearable tape.

Henkel Consumer Adhesives, Inc.
Avon, OH 44011-1355
Jan 23, 2007 Hysol® FP5110 offers adhesion to 2- and 3-layer flexible printed circuits by bonding to polyimide and epoxy adhesive material. It provides an alternative to mechanical soldering by bonding bumps to substrate through lead-free compatible thermal compression process that eliminates need for flux application, reflow, and cleaning. Other features include 10 sec SnapCure at 180°C, storage requirements of -15°C, and compatibility with ultrasonic bonding processes.