Dielectric Polymers, Inc., Div. Of Adhesive Applications, Inc.
Holyoke, MA 01040
Dec 21, 2006 Self-wound NT-5511-2SW and 5512-2SW address issues related to material loss, registration, and waste disposal for converters of roll label stock and substrates to be coated with pressure sensitive adhesive. Polyester film backing coated with high-temperature yellow silicone adhesive on unwind side and easy release silicone coating on backside allow adhesive release at splice area, eliminating label loss. Both products facilitate splicing of siliconized webs.

Scapa Medical
Inglewood, CA 90302
Dec 13, 2006 Made for direct skin contact, medical-grade silicone gels are available in various breathable thermal co-polymer films and non-woven materials. Products may be removed, cleaned, and reused, as they wash off with water and regain adhesion when properly dried. Areas of use include neonatal care, wound care, medical device attachment, and hypertrophic scarring reduction.

ExxonMobil Chemical
Houston, TX 77079-1398
Nov 28, 2006 Santoprene(TM) thermoplastic vulcanizate (TPV) B100 bonds with engineering thermoplastics such as ABS, polycarbonate, polystyrene, acrylic, acrylonitrile styrene acrylate, PET, and polyphenylene oxide/PS blends using cold insert, 2-shot injection or extrusion molding. Dishwasher- and microwave-safe, non-hygroscopic elastomer is compliant with FDA regulations for food/liquid contact and can reduce need for multiple-component assembly.

NYLOK Corp.
Macomb, MI 48042 4007
Nov 27, 2006 Effective in working temperatures from -40 to +300ºF, NYPLAS® is pre-applied under heads of fasteners, rivet nuts, pop-style rivets, and double-ended flange screws to seal out water, moisture, dust, and air. Plastisol (PVC) material coating dampens rattles and noises while eliminating leak path under head. Reusable, non-toxic product will not shrink or dry out with age and does not require gasket seals, sealant compounds, or other in-house assembly sealants.

Aremco Products, Inc.
Valley Cottage, NY 10989
Nov 27, 2006 Used in applications requiring bond strengths up to 4,770 psi, 2-part, ceramic-filled Aremco-Bond(TM) 2310 is gray-pigmented, 100% solids epoxy adhesive with flexural strength of 12,000 psi, volume resistivity of 3.0 x 10¹³, dielectric strength of 410 V/mil, and dielectric constant of 4.28 at 1 kHz. Cured product exhibits linear shrinkage of .001 in./in. and Shore-D hardness of 78. Recommended cure is 2 hours at 150°F or 48 hr at room temperature.

Hexis USA LLC
Corona, CA 92880
Nov 22, 2006 Available in rolls 54 in. wide and 98.4 in. long, CSE25 and CSR25 are white matt heavy-gauge vinyl films with adhesive layer. Offering strong, permanent adhesion, 7.9 mil CSR25 is suited for grained surfaces such as smoothened concrete and rough paint finishes. Providing removable adhesive and high release liner, 7.9 mil CSE25 is intended for temporary indoor applications, such as store windows, sign boards, and other flat surfaces.

Datalase Inc
Cheshire WA8 8FW  United Kingdom
Nov 17, 2006 Offering label replacement for outer case secondary packaging, DataLase® CASEMARK Tape does not have any backing paper and does not require inks or ribbons. It changes from white to black upon exposure to low power CO2 laser. Apply-and-print technique enables information to be printed on tape after it has been applied to case. If tape is removed from carton after imaging has occurred, image is automatically transferred to box, leaving permanent image as evidence.

Master Bond, Inc.
Hackensack, NJ 07601
Nov 16, 2006 Featuring set-up time of 8-12 min at 75°F, room temperature cure MasterSil 415 one component silicone elastomer has dielectric strength of 500 V/mil and service temperature range of -185 to 400°F. Resistant to vibration, impact, and shock, it has Shore A hardness of 30, elongation of 400 at 75°F, and tensile strength of 325 psi. Compound can be applied on vertical surfaces without sagging or running, and cures to flexible, rubbery solid when exposed to atmospheric moisture.

NuSil Technology
Carpinteria, CA 93013
Nov 14, 2006 Low outgassing, one-part material EPM-2411-2 glop-top is designed for encapsulation of chip packages in devices where outgassing-related contamination poses problem. Product exhibits low stress and wide operating temperature ranges characteristically associated with silicone-based materials. It is stored and shipped frozen in 3 and 30 cc syringes as well as 3 and 6 oz tubes.

Rollprint Packaging Products, Inc.
Addison, IL 60101
Nov 08, 2006 Extrusion coated onto various substrates such as film, foil, or paper, Allegro® M helps achieve clean peel. It seals to rigid cup or tray structures including HIPS, PVC, APET, PP, and HDPE. Allegro M helps lidding structures stand up to transport challenges, minimizing chance of compromise. Typical applications include unit-of-use liquid medications, diagnostic cartridges, pre-filled syringes, and medical devices.

Master Bond, Inc.
Hackensack, NJ 07601
Oct 20, 2006 With 3-minute set-up time, EP51M produces bonds with 2,000+ psi shear strength that exhibits resistance to thermal cycling and chemicals. Bonded parts can be safely handled within 30 min. Product, suited for cryogenic applications, adheres to metals, glass, ceramics, wood, vulcanized rubbers, and plastics. Insensitive to cleaning procedures, it can be used in electronic, electrical, computer, construction, metalworking, appliance, automotive, and chemical industries.

Superior Epoxies & Coatings, Inc.
Decatur, GA 30035
Oct 19, 2006 Featuring 100% solids formulation, chemical-resistant Superior Cove Kit is designed for vertical application at floor-wall joints to produce sanitary perimeter seal. This structural epoxy mortar, packaged in pre-measured kits to cover 35 lineal feet (4 in. vertical and 2 ft horizontal at 1/8 in.), requires clean surface prepared via sand blasting, water blasting, or other mechanical means. Each kit contains binder and blended aggregate in plastic mixing container.

Master Bond, Inc.
Hackensack, NJ 07601
Oct 18, 2006 Environmentally friendly UV15DC80, suited for bonding, sealing, coating, and potting, requires no mixing and has 100% solids formulation. Uninhibited by oxygen, chemically resistant epoxy contains no solvents or volatiles and adheres to variety of materials. For thicknesses of .010-.020 in., straight UV curing is accomplished within seconds with UV light at 365 nm with 30-40 mW/cm² of energy. Product also cures in shadowed areas with supplemental heat at 80°C for 15-30 min.

Hexis USA LLC
Corona, CA 92880
Oct 16, 2006 With liner and adhesive compound that make product repositionable during application, HX200WG1 and HX201WG1 High Performance Vinyls feature polyethylene liner that is insensitive to humidity and temperature changes. HX200WG1 has structured gray adhesive liner and HX201WG1 has clear permanent liner. Standard roll sizes are 148 ft long and 54 or 63 in. wide.

Adchem Corp.
Riverhead, NY 11901
Oct 10, 2006 Multipurpose 4377M and 4380M have rubber-based adhesive coating on liner side and acrylic adhesive coating on exposed side. Design allows exposed side of adhesive to bond to 30+ foam materials, including urethanes, epichlorohydrins, and EPDM blends, while liner side of adhesive bonds to surfaces such as talc-filled polypropylene, mica-filled polypropylene, and mineral-filled nylons. Tapes suit automotive industry applications with strict insulation and sound reduction requirements.

Scapa North America
Windsor, CT 06095
Oct 09, 2006 Designed for automotive applications, P1058A bonds to low surface energy plastics and offers resistance to abrasion and environmental extremes. It consists of black, 36 mil precision cut nylon flock material, single-coated with automotive-grade acrylic adhesive. Product is supplied with 83 lb polycoated release liner to facilitate die cutting. It meets requirements of Ford ESB-M6G17-A, General Motors GM6420M, and Daimler Chrysler MS-JZ8-22 specifications.

Aremco Products, Inc.
Valley Cottage, NY 10989
Oct 09, 2006 Aremco-Seal(TM) 617 is used to produce hermetic seals in porous ceramics and refractories in electrical and high-vacuum applications. Single-part, water-based glass coating, applied by dipping, brushing, or spraying, cleans up prior to curing with warm water. Curing is accomplished by setting at room temperature for 30 min and then heating to 1,600°F for 30 min. Odorless product contains no VOCs, and no outgassing will occur upon curing or during operation.

Scapa North America
Windsor, CT 06095
Oct 04, 2006 Unifilm® U797A low fogging acrylic transfer adhesive bonds to low surface energy materials and is formulated for gasketing as well as noise, vibration, and harshness reduction applications. Transfer adhesive is 5 mil thick and is supplied with 83 lb natural polycoated release liner. Offering high tack, quick stick and peel strength, adhesive performs over wide temperature range and is resistant to water, humidity, and chemicals.

Aremco Products, Inc.
Valley Cottage, NY 10989
Oct 02, 2006 Ceramacast(TM) 646N is hydraulic-setting, phosphate-bonded, zirconium oxide filled ceramic compound used for encapsulating and potting high temperature electrical components to 3,000ºF. Supplied as dry powder, potting compound sets hydraulically in 16-24 hr at room temperature. Cured material demonstrates volume resistivity of 10⁹ W-cm and dielectric strength of 250 V/mil.

Master Bond, Inc.
Hackensack, NJ 07601
Oct 02, 2006 Designed for high performance bonding, sealing, and casting, Model EP21TDC-4HT epoxy compound resists vibration, impact, and shock, and can be room temperature or heat-cured. High physical strength properties include tensile strength of 8250 psi, tensile shear strength of more than 2800 psi, and peel strength exceeding 36 pli at 25°C. Featuring volume resistivity greater than 1014 ohm-cm, two-part epoxy bonds with metals, glass, ceramics, wood, vulcanized rubbers, and most plastics.