Adhesives & Sealants

Adhesives & Sealants, Materials & Material Processing, Mounting & Attaching Products

High-Temperature Sealant suits applications to 950°F.

April 24, 2015

Formulated by combining high-temperature resin with ceramic fibers and powders, Pyro-Putty™ 950 can be used as gasketing compound for boilers, compressors, heat exchangers, furnaces, ovens, and exhaust manifolds. Product repairs rough, scored, or irregular surfaces and is resistant to chemical and steam attack, high pressure/vacuum atmospheres, mechanical vibration, and joint movement. Offered... Read More

Adhesives & Sealants, Paints & Coatings

Two-Part Epoxy Paste has ultra low thermal resistance.

April 7, 2015

Master Bond EP48TC has thermal resistance of 5–7 x 10–6 K•m2/W, which enables thermal conductivity of 20–25 BTU•in/ft2•hr•Â°F. Applied in bond lines as thin as 10–15 microns, epoxy paste has tensile lap shear strength from 900–1,100 psi and bonds to metals, composites, glass, ceramic, and plastics. Working life for 100 gram batch at 75°F is 90–120 min. Curing at room... Read More

Adhesives & Sealants, Materials & Material Processing

Epoxy Potting Compound resists high temperatures.

March 27, 2015

With 130°C relative temperature index rating, 50-3150RFR Black Epoxy with Catalyst 30 will survive elevated temperatures for long periods of time, which offers benefits as electronics get smaller and hotter. Compound is UL 746B listed and formulated to meet stringent non-burning requirements of UL 94 V-0. Typical applications include encapsulating power supplies, transformers, coils,... Read More

Adhesives & Sealants

Needle-Bonding Adhesive facilitates cure confirmation, inspection.

March 27, 2015

With viscosity of 150 cP, 1405-M-UR-SC is formulated with Encompass™ technology that incorporates See-Cure color change and Ultra-Red™ fluorescing technologies with LED-curing capabilities. Medical device adhesive is blue in uncured state to aid placement verification and fluoresces bright red under 365 nm black light after cure. Suitable for bonding stainless steel, PC, PMMA, and ABS,... Read More

Adhesives & Sealants

Epoxy Stick facilitates fuel tank repairs.

March 25, 2015

Offering resistance to ethanol and most solvents, Permatex Fuel Tank Repair Epoxy Stick is suited for filling holes and damaged seams in both metal gas tanks and containers. Product comes as 2-part putty in stick form which helps measure and mix proper amount. Finished repair sets in just 1 hour and can be drilled, sanded, threaded, or filed after 5 hours. When fully cured, epoxy withstands... Read More

Adhesives & Sealants

Dr. Wusheng Yin, to Speak at IMAPS New England Symposium and Expo 2015

March 25, 2015

Albany, NY - Dr. Wusheng Yin, President of YINCAE Advanced Materials LLC, will be presenting in the Technical Sessions on "The Future of Solder Joint Encapsulation" at the upcoming IMAPS New England Symposium and Expo 2015. The conference will be held on May 5th at the Holiday Inn Conference Center in Boxborough, Massachusetts. The topic of the session focuses on the issues the electronics... Read More

Adhesives & Sealants, Materials & Material Processing

Lubrizol Highlights Innovative Polymers at NPE 2015

March 24, 2015

CLEVELAND – Lubrizol Engineered Polymers announces that it will be showcasing several of its new and/or expanded polymer solutions at NPE 2015—The International Plastics Exposition—in Orlando, FL from March 23-27, in the South Hall, Booth #S12073. A global leader in supplying polymer solutions, Lubrizol will be highlighting its innovative offering including:         ... Read More

Adhesives & Sealants, Materials & Material Processing

Garlock Discontinues Style ST 706. Equalseal.com Introduces a Performance Equal

March 19, 2015

Because Garlock Sealing Technologies discontinued offering style ST-706 inorganic fiber gasket material in May 2014, Equalseal.com now offers a replacement and performance equal. Equalseal EQ706 EQ706 (Black) is a premium grade, in-organic fiber and NBR sheet formulated for high temperatures applications. Recommended for use in sealing against both saturated and superheated steam, along with high... Read More

Adhesives & Sealants

Conductive Adhesive electrically connects solar cells.

March 6, 2015

Stress absorbing to withstand rigors of thermal cycling, DB-1541-S9 is suited for stringing or shingling applications in crystalline silicon and thin-film solar modules. Adhesive electrically connects solar cells using ribbons or direct cell to cell contact. Providing optimized conductive stability to cell and ribbon metallization during damp heat exposure, adhesive is designed to gel rapidly and... Read More

Adhesives & Sealants, Health, Medical, & Dental Supplies and Equipment

Medical Tapes for Wearable Sensor Devices: MBK Provides Innovative Tape and Design Solutions

March 3, 2015

Chatsworth, CA – Bio-compatible skin friendly medical adhesive tapes are an integral part of designing wearable sensor medical devices. Wearable sensor devices are used to monitor, diagnose and treat diseases from monitoring glucose, blood pressure, bodily fluids, ECG and heart rate, including delivery of medical drugs and nutraceuticals to the skin surface. The challenge for startups and... Read More

Adhesives & Sealants, Materials & Material Processing, Printing & Duplicating Equipment

Electrically Conductive Inks suit wearable electronics.

March 2, 2015

Adhering to variety of natural and synthetic fibers, 125-19FS consists of flexible, screen-printable, silicone-based conductive ink that offers low-temperature performance to -70°C, and high temperature properties up to 325°C. Screen-printable 120-07 Ink is extremely conductive with optimal creasing resistance and washability features. Adhering to fabric substrates, 124-33... Read More

Adhesives & Sealants, Fasteners & Hardware

Machinists Inc. Steps in to Provide Needed Fix for City of Seattle

February 25, 2015

Machinists Inc. had an opportunity to work on a special project in West Seattle with Seattle Public Utilities (SPU), where the aging, 1930s era water system, was giving the city of Seattle some problems. A pressure valve there has been leaking water into a reservoir for a number of years. Because of erosion, it had created a non-sealing surface, so it wouldn't seal tight. It meant the city of... Read More

Adhesives & Sealants, Materials & Material Processing

Henkel to Debut New Solder Paste, Highlight Novel Protection and Thermal Materials at APEX 2015

February 23, 2015

At the upcoming APEX event, set to take place February 24 – 26 in San Diego, California, The Electronics Group of Henkel plans to unveil a breakthrough solder material, showcase several novel innovations that are lending new levels of protection and performance to next-generation devices and introduce the line of Bergquist thermal management materials. On day one of the show, Henkel plans to... Read More

Adhesives & Sealants

Thermoplastic Adhesive suits temporary mounting applications.

February 17, 2015

Adhering to ceramics, glasses, and metals, Crystalbond™ 509 is suitable for temporarily mounting substrates that require dicing, grinding, or polishing operations. Thermoplastic adhesive is applied by preheating mounting plate to 250°F, melting and spreading adhesive in uniform layer, then positioning part over adhesive, allowing entire assembly to cool. After processing, Crystalbond™... Read More

Adhesives & Sealants, Chemicals & Chemical Processing, Health, Medical, & Dental Supplies and Equipment

Soft Silicone Adhesives suit skin applications.

February 11, 2015

Designed specifically for wound care, Silbione® HC2 2022 medium-viscosity silicone gel is compatible with most coating processes and applicable on wide range of substrates, including PU films, perforated films, and open knit fabrics. Product is manufactured in ISO 8 clean room in ISO 13485 facility to ensure microbial safety on breached skin. For wearable devices, scar management, and... Read More

Adhesives & Sealants, Chemicals & Chemical Processing, Green & Clean

Acrylic Resins suit ultra-low VOC coatings.

February 10, 2015

Suited for 2-component concrete coatings, MAINCOTE™ AEH Acrylic Epoxy Hybrid combines weatherability and UV resistance of acrylics with chemical resistance of epoxies. Product offers tire pickup resistance in waterborne 2K concrete coatings as well as resistance to aggressive cleaning regimens. With VOC levels of 50 g/L or less, MAINCOTE™ 4950 Acrylic Resin is suited for direct-to-metal... Read More

Adhesives & Sealants, Chemicals & Chemical Processing

WACKER and Inpro Develop a New Silicone Adhesive for Plastic Oil Pans

February 10, 2015

Munich — Munich-based chemical Group WACKER, and inpro Innovationsgesellschaft für fortgeschrittene Produktionssysteme in der Fahrzeugindustrie mbH have developed a silicone adhesive-sealant for mounting vehicle oil pans. Sold under the name ELASTOSIL® RT 779, the new product adheres to both aluminum and polyamide. Plastic oil pans can now be mounted without mechanical fasteners.... Read More

Adhesives & Sealants

Fast Cure Adhesives suit cartridge dispensing.

February 4, 2015

Suitable for use with TriggerBond® dispensing guns, TriggerBond Epoxies offer shear strength up to 1,500 psi and notched Izod impact of 2.7 ft-lb/in. Adhesive's 2 components are packaged into cartridges, which fit in dual-barrel dispensing gun. Because cartridges contain precise quantities of hardener and resin, TriggerBond produces correct mix ratio every time user squeezes trigger.... Read More

Adhesives & Sealants, Materials & Material Processing, Paints & Coatings

European Coatings Show 2015: WACKER Presents Innovative Binders and Hydrophobic Agents for Gypsum Applications

January 30, 2015

Munich, – At the European Coatings Show (ECS) in Nuremberg, Germany, from April 21 to 23, 2015, the Munich-based WACKER Group will be exhibiting a new polymeric binder for modifying gypsum drywall products. VINNAPAS® 4800 G gives gypsum-based joint fillers outstanding tensile adhesive strength on gypsum plasterboard and jointing tapes. Joint fillers finished with this new dispersible polymer... Read More

Adhesives & Sealants, Paints & Coatings

METALAST Surface Technology has Become a Woman Owned Small Business (WOSB) Providing (MIL-SPEC) Surface Technology Solutions to Federal and Military Partners

January 30, 2015

Minden, NV. —  METALAST Surface Technology, LLC (MST) announces registration with the SBA as a Woman Owned Small Business (WOSB). www.metalast.com For years, METALAST Surface Technology’s chemistry, training, and services have provided support to numerous Government and Military entities. In the current phase of business, METALAST has emerged as a... Read More