Devcon    Danvers, MA 01923
Feb 04, 2004 ZipGrip® adhesives consist of clear-drying cyanoacrylates that bond plastics, rubber, and metal; provide flexibility and impact resistance; and withstand service temperatures to 280°F. Able to attain fixture strength in seconds, adhesives reach functional strength in 60 min and full cure in 24 hr. ZipGrip HV1200 has 1,200 cps viscosity and 3,700 psi tensile shear strength, while ZipGrip HV2200 has 2,200 cps viscosity and 3,800 psi tensile shear strength.

MACtac, Technical Products Division    Stow, OH 44224 1888
Feb 04, 2004 Intended for medical devices where skin contact is possible, TM9616 consists of 1/16 in. white polyethylene foam, double-coated with acrylic-based, hypoallergenic, medical-grade adhesive. Adhesive is protected by semi-bleached kraft release liner with silicone release system on 2 sides. Product is formulated for sustained contact with human skin. Applications include ostomy mounts, electrosurgical grounding pads, and multi-function electrodes.

Aremco Products, Inc.    Valley Cottage, NY 10989
Feb 04, 2004 Pyro-Putty® 2400 thermally conductive adhesive, sealant, and metal repair compound is suited for applications up to 2,000°F. Ceramic and stainless steel-filled paste bonds, seals, and repairs defects up to 3/8 in. cross-section in cast iron, steel, and stainless steel components. Single-part, thermally shock-resistant product is water-based and contains no VOCs. It sets at room temperature and cures in-situ or by heating to 200°F for 2–4 hr.

Cotronics Corp.    Brooklyn, NY 11232
Feb 04, 2004 Offered as alternative to anaerobic sealants, Resbond(TM) 507TS is non-corrosive; adheres to threads, studs, and pipes; and cures to form thermally stable and electrically insulating joints. Product prevents vibration loosening and leakage caused by shock and vibration in high-temperature applications. Preparation requires users to mix and apply, and product cures in 2-4 hr at room temperature. Material has no flammable solvents or harsh odors.

Mapei    Deerfield Beach, FL 33442
Jan 29, 2004 Mapelastic HPG prevents movement of moisture into sub-surfaces of structures that can cause swelling, wood rot, and leaks. Creamy fluid can be applied with trowel, brush, or roller to prevent transfer of cracks through membrane and into tile or stone above it. Membrane meets all requirements for VOC compliance and incorporates BioBlockâ„¢ antimicrobial protection, which inhibits mold and mildew growth.

Adhesives Research, Inc.    Glen Rock, PA 17327
Jan 28, 2004 ARclean® 90178 and 90176 are 0.0035 and 0.005 in. thick non-corrosive tapes that provide perimeter spacer bonding in resistive touch screen and other similar electronic devices. They utilize electronically-clean, acrylic acid-free adhesive, and have low outgassing of VOCs. Tapes offer resistance to aging with ability to withstand temperature and humidity extremes. Both have polyester film carrier as dielectric barrier between bonded conductive surfaces.

Tra-Con, Inc.    Bedford, MA 01730
Jan 23, 2004 Thermally-conductive TRA-BOND 224-8 can cure in 4 hours at room temperature or as short as 3 min at 95°C. It offers 30 min work life and shelf life up to 1 year. Viscosity of 20,000 cp ensures that adhesive will flow into most small voids and creases. Combined with electrical insulator, product is suited for encapsulation, component staking, and sealing. Package options include BI-PAX and premixed, frozen syringes.

Balzers, Inc.    Elgin, IL 60123
Jan 22, 2004 G6 BALINIT® wear-resistant, AlCrN-based coating is oxidation-resistant and exhibits stability even at thermal load extremes. Physical Vapor Deposition (PVD) coating is directed specifically toward applications that allow coating and re-coating of carbide and HSS tools.

Aremco Products, Inc.    Valley Cottage, NY 10989
Jan 21, 2004 Ceramabondâ„¢ 552 consists of single-part, alumina-filled adhesive that adheres to ceramics and metals used in applications to 3,000°F. Dispensable adhesive is water-based, environmentally safe material that contains no VOCs. After setting at room temperature and curing at 200°F and 500°F for 2 hr, respectively, it resists acids, solvents, fuels, and molten metals. It exhibits dielectric strength of 250 V/mil and tensile shear strength of 450 psi.

ITW Devcon Futura Coatings    St. Louis, MO 63132-1021
Jan 21, 2004 Ceramic Coat® epoxy system is formulated to repair, rebuild, and protect surfaces subject to corrosion or wear, negating need for replacement parts. After reframing, damaged blades can be rebuilt to original specifications with trowelable CT 3000® and then protected with brushable Ceramic Coat 4000®. Applications include pump casings, impeller blades, suction plates, gate and butterfly valves, water boxes, tube sheets, and heat exchangers.

Henkel Loctite Corporation    Rocky Hill, CT 06067
Jan 20, 2004 Hysol® QMI 550EC silver-filled, conductive adhesive bonds integrated circuits and components to advanced substrates such as PBGAs, CSPs, and array packages. It produces void-free bond line with interfacial adhesion to variety of organic and metal surfaces. Hydrophobic product can be cured in-line using Skip-Cure processing in just 10 seconds after bond line reaches 150°C. Hysol® QMI 550EC meets JEDEC Level 3 standards for 260°C reflow applications.

Berry Plastics Corp., Tapes & Coatings Division    Franklin, MA 02038
Jan 16, 2004 Tyco Polyken® 007 consists of non-woven polyester backing on black natural rubber adhesive that is single-coated, self-wound, and provides consistent unwind throughout roll. Conformable and abrasion-resistant product, non-corrosive to copper wire, measures 11 mil thick and ¾ in. wide and has 20 lb/in. tensile strength. Applications include spot taping, clip retention, or continuous wrap applications where sound dampening is desired.

Chemline Inc.    St. Louis, MO 63103
Jan 15, 2004 EURO-SEAL 7000 polyurethane encapsulant, suited for use on carved architectural EPS and polyurethane foam elements, provides protection from thermal expansion and UV degradation and strengthens mechanical impact resistance. Able to dry to touch within 10 sec, 2-component, spray-applied polyurethane coating forms hard, chemical-, moisture-, and fire-retardant encapsulation. It enables fabricators to coat foam parts in production-line fashion.

Tra-Con, Inc.    Bedford, MA 01730
Jan 12, 2004 Tra-Bond 813J01 offers thermal conductivity constant of 1.1 W/M/°K, making is suited for encapsulating heat generating devices such as transformers, thermistors or power sources, and pour-in-place heat sinks. Operating temperature is 260°C, but with Tg of -120°C, Tra-Bond 813J01 can deal with stress issues and mismatched CTEs. It can be cured at room temperature, or in only minutes at elevated temperatures. Working life is 100 min.

Tra-Con, Inc.    Bedford, MA 01730
Jan 12, 2004 Clear, medium-viscosity Tra-Bond 2105 contains no solvents or other additives that could be harmful to environment or users. It bonds to glass, ceramics, most plastics, and metals. Product can be heat or room temperature cured and passes cytotoxicity ISO elution method. It is recommended for applications such as repair of fiber optic connectors, electronic and aerospace systems, medical device assembly, and structural laminating applications.

Scapa North America    Windsor, CT 06095
Jan 02, 2004 Clear, low-density Scapa P933A bonds to common industrial substrates and withstands environmental extremes. It is single-coated with acrylic adhesive formulated to provide high tack, quick stick, and peel strength, while offering humidity, water, and chemical resistance. Able to adhere to metals and engineering plastics, tape features release top-coat that allows film to be converted into self-wound product.

Henkel Loctite Corporation    Rocky Hill, CT 06067
Jan 02, 2004 Loctite® 4851(TM) and 4861(TM) clear instant adhesives, suited for use on tubing, o-rings, rubber, paper, leather, and fabric, are formulated to provide reduced hardness. Loctite® 4851(TM) medium-viscosity, single-component adhesive performs general-purpose bonding, while Loctite® 4861(TM) high-viscosity, single-component adhesive bonds porous and absorbent materials. Both offer thermocycling resistance and bond to metal, plastic, or elastomeric materials.

Henkel Loctite Corporation    Rocky Hill, CT 06067
Jan 02, 2004 Low-viscosity Loctite® FLASHCURE(TM) 4306(TM) and medium-viscosity Loctite® FLASHCURE(TM) 4307(TM) offer instant fixture and tack-free surfaces in less than 5 sec when exposed to low-, medium-, or high-intensity light. They are surface insensitive and adhere to metals, elastomers, and plastics. Designed for assembly of components where ability to verify presence of applied adhesive is desired, they deliver minimal blooming and stress cracking on sensitive substrates.

Tra-Con, Inc.    Bedford, MA 01730
Dec 30, 2003 Clear, low-viscosity (500 cps) Tra-Cast 3010 bonds to ceramics, glass, metals, and plastics. With 65 Shore A hardness and operational temperature range of -70 to 105°C, product is suited for aerospace and electronic applications. Fully cured adhesive acts as electric insulator and is resistant to weathering, gases, vapors, petroleum products, and harsh chemicals. It has volume resistance of 10¹² ohm-cm and work life of 8 hr.

Tra-Con, Inc.    Bedford, MA 01730
Dec 22, 2003 High-temperature TRA-BOND 526M02 features glass transition temperature of over 150°C and can be heat-cured in as quickly as 10 min at 140°C. It adheres well to most metals, plastics, glass, and ceramics. Product exhibits resistance to most petroleum products, many vapors and gases, and many organic compounds. Applications include potting glass fibers, bonding fiber bundles, and terminating connectors.