New Transceivers Products

RF Transceiver targets short-range wireless systems.

Housed in 5 x 5 mm 32-pin LFCSP package, dual-mode Model ADF7242 supports IEEE 802.15.4 based protocol standards at 250 Kbps as well as proprietary protocols up to 2 Mbps using GFSK/FSK modulation schemes. Transmit and receive paths provide blocking resistance that allows device to operate in crowded 2.4 GHz band and prolongs battery life in smart meters/smart grid, wireless sensor networks,...

Serial Transceiver supports RS-232, RS-485, and RS-422.

Model SP336, 3.3 V/5.0 V single-chip serial transceiver features both RS-232, RS-485, and RS-422 drivers and receivers. It supports full or half duplex configuration and also includes diagnostic loop-back function. Configurable into 8 operating modes, multiprotocol unit protects all bus pins against ESD up to Ã-

SSI Module enables absolute encoders to go wireless.

Using SSI communications protocol at transmitter and receiver end, SwiftComm(TM) Wireless Interface allows critical position and speed feedback data to be seamlessly sent to control systems without cabling. Interface works with any SSI position device or other type of SSI sensor and provides built-in reliability needed for real-time industrial control. Transmitter-receiver pair communicates using...

Transceiver Modules streamline fiber optic digital video.

Available in standalone or rack-mount card versions, fiber optic digital video transceiver modules are suited for use in CCTV monitoring systems and intelligent transportation systems. They support transmission of video over one optical fiber and ensure proper system operation in complex electromagnetic environments. Compatible with NTSC, PAL, and SECAM video formats, hot-pluggable units use...

Understanding Crane and Hoist Classifications

Building success: Crane & Hoist Design Criteria

PHY Transceiver supports IEEE 802.3 10GBASE-T operation.

Featuring dual port configuration, Model BCM84812 supports two 10 GbE ports and provides complete PHY solution consuming less than 6 W of power/port while operating over 100 m of Cat 6A UTP or Cat 7 cables. Transceiver is optimized to enable switch, controller, and other general 10 GbE connectivity applications with 4-lane, 3.125 Gbps XAUI interface that enables connectivity to 10 GbE media...

3G Wireless Modules Internet-enable electronic devices.

With speeds to 3.1 Mbps (downlink) and 1.8 Mbps (uplink), DTP-500D CDMA module operates on EVDO Rev A 800 and 1,900 MHz wireless networks. It offers GPS/AGPS location capabilities, built-in TCP/IP stack, and USB 2.0 interface. Operating globally on tri-band UMTS 850/1900/2100 wireless networks as well as quad-band GSM/GPRS/EDGE 850/900/1800/1900 networks, DTP-600W HSPA module transmits data at...

Laird Technologies' Vehicle M2M Device Chosen by Guidepoint Systems

Exceptional Technology, Highly Reliable, and Competitively Priced St. Louis, Missouri, USA - March 25, 2009 - Laird Technologies, Inc., a global leader in the design and supply of customized, performance-critical components for wireless products and advanced electronics, today announced its Vehicle M2M Device customized for use with Guidepoint Systems' service. Guidepoint selected Laird...

PHY Devices target 10 GbE SFP+ applications.

Designed using 65 nm process, BCM8727 dual 10 GbE SFI-to-XAUI PHY and BCM8750 dual 10 GbE SFI-to-XFI PHY solutions implement electronic dispersion compensation equalizer technology that uses all-DSP design. Devices incorporate multi-tap transmit pre-emphasis to compensate for FR-4 board material loss in line card applications. They support backward compatibility using existing 1 GbE SFP modules,...

SFP Transceiver provides 40 km data link over single fiber.

Suited for high-speed datacom applications, 2.5 Gb/s hot pluggable SFP Transceiver features upstream 1,310 DFB laser and downstream 1,490 PIN/TIA receiver. Bi-directional, optical transceiver is based on SystemOnGlass(TM) technology, which consists of mountable glass chip that integrates commercial laser diodes, photodiodes, and minimum number of electronic and electro-optic components using no...

CWDM Transceivers feature SFP design.

Compatible with SFP (small form-factor pluggable) modules, including those from CISCO, HCDTR series is designed to support SONET, Gigabit Ethernet, Fiber Channel, and other communication standards. Areas of use include telecommunication and data communication applications.

Von Ruden's Driven Tools Are Built to Last

Von Ruden's driven tools are designed to each specific machine in order to maximize performance. All of our tools are performance tested and made in the USA per ISO 9001:2015 standards. Check out our video to learn more.