Sealants

Elastomeric Sealant fastens expansion and construction joints.
Sealants

Elastomeric Sealant fastens expansion and construction joints.

Belzona® 4521 Magma-Flex Fluid is a low modulus, 2-component material that extends and compresses with thermal movement of building and structures, ensuring minimal bond-line stress. It cures quickly and is moisture tolerant. Belzona® 4521 remains permanently elastic, requires no heating, and has no shrinkage. It adheres to concrete, stone, steel, and other polymers. Sealant is...

Read More »
Floor Care System eliminates use of hazardous chemicals.
Coatings

Floor Care System eliminates use of hazardous chemicals.

EnviroStar Green FloorCare System meets or exceeds domestic and international standards. Five products work together to deliver wet-look shine and safety, including EnviroStar Green Floor Coating, Sealer, All-Purpose Cleaner, Maintainer, and Stripper. Products do not have ethylene glycol based solvents, bioaccumulative fluorocarbon surfactants, alkyl phenol ethoxylate surfactants,...

Read More »
Ceramic-Silicone Sealant handles temperatures to 2,000°F.
Sealants

Ceramic-Silicone Sealant handles temperatures to 2,000°F.

Non-flammable, environmentally safe, single-part, water-dispersed Aremco-Seal(TM) 4030 seals porous ceramics and refractories. Formulated with viscosity of 600-1,200 cps, product is applied by brush, roller, or spray equipment, drying at room temperature in less than 1 hr with full cure in 30-60 min @ 450°F. Solids content is 40% and theoretical coverage rate at 1 mil is 535 ftÂ-²/gal....

Read More »
Urethane requires only one coat.
Coatings

Urethane requires only one coat.

High-build, fast-drying, direct-to-metal Fast Clad(TM) DTM Urethane can be applied at 6-9 mils DFT in single coat with no outgassing or pinholing. Urethane dries in 1 hour as corrosion-resistant finish and may be applied at temperatures as low as 35°F, with airless spray equipment, brush, or roller. Coating has 2-hour potlife at 77°F and is for use directly over properly prepared...

Read More »
Black Aerosol Foam comes in seamless, leak-proof can.
Sealants

Black Aerosol Foam comes in seamless, leak-proof can.

SuperSeal® Duct Butter's aerosol can will not leak or corrode, increasing its shelf life and stability. Product retains its shape and volume after curing is completed, resulting in improved finished appearance. Used for spot and edge repair of ductboard or liner, it can also be used to seal gaps between liner sections or fittings. SuperSeal maintains thermal integrity of insulation it is...

Read More »
Threadlocker/Sealant replaces lockwashers.
Threadlockers

Threadlocker/Sealant replaces lockwashers.

PERMABOND® HH120 seals fasteners against water and chemicals. It obtains fixture strength in 15-20 min on active metals such as iron, steel, nickel, and aluminum. Viscosity is 7000 cp, allowing for gap filling up to 10 mil. HH120 features locking strength of 250-350 lb-in. and retaining strength of over 2000 psi. It is suitable for locking bolts, nuts, and screws for permanent assembly, and...

Read More »
Sealants

Sealant penetrates porosity in powder metals.

Loctite® PM 5120 plating grade sealant is intended for shallow penetration to seal against low pressure plating operations. Durable enough to resist strong acids and bases at low temperatures, sealant is formulated for controlled cure at room temperature on active metal substrates to avoid bleed out. Fluorescent dye facilitates cross-sectional inspection. Loctite PM 5120 is easy to recover...

Read More »
Adhesive/Sealant has service range of -75 to 500°F.
Adhesives

Adhesive/Sealant has service range of -75 to 500°F.

Polymer System X5HT one component, contact type adhesive/sealant offers dimensional stability and creep- and chemical-resistance. Curing process requires application to each substrate, application of pressure (less than 50 psi), and curing at 300 to 400°F for 15 to 30 min in vented oven. X5HT adheres to metals, polymers, composites, glass, and ceramics. Lap shear strength values range from...

Read More »
Sealant is suitable for construction market.
Sealants

Sealant is suitable for construction market.

Available in gun-grade cartridges and sausage packs, Chem-Calk® 2000 one-Part, solvent-free, multi-function sealant has 30 minute skin time. Its cures at 77°F with 50% relative humidity to 1/4 in. thickness in 24 to 36 hours. After 14 days of full cure, it provides resistance to ozone, ultra-violet light exposure, heat, and aging. Product offers tensile strength of 260 psi, modulus...

Read More »
Ceramic Coating seals thermal spray coatings.
Coatings

Ceramic Coating seals thermal spray coatings.

Ceramacoat(TM) 503-VFG-S ceramic-based sealant is formulated as single part, water-dispersible, alumina-filled system. Inert, chemically resistant, inorganic material does not outgas or decompose in high temperature corrosive applications to 3200°F. Applied using sponge brush or pneumatic spray equipment, full cure is achieved after exposure for 1-2 hours at 700°F. It sinters and...

Read More »

All Topics