Sealants

Sealants

Foam Sealant has wide operating temperature range.

Formulated for low-humidity conditions, Handi-Foam® Extreme cures at temperatures from as low as -20°C to seal, fill, bond, and stop air infiltration. Closed-cell polyurethane foam sealant also helps prevent moisture infiltration, reducing water damage and mold problems. This is particularly of use in areas where freeze/thaw cycles are common. Formula promotes low-temperature flow...

Read More »
Silicone Elastomer suits optical and display applications.
Silicone

Silicone Elastomer suits optical and display applications.

Featuring set-up time of 8-12 min at 75°F, room temperature cure MasterSil 415 one component silicone elastomer has dielectric strength of 500 V/mil and service temperature range of -185 to 400°F. Resistant to vibration, impact, and shock, it has Shore A hardness of 30, elongation of 400 at 75°F, and tensile strength of 325 psi. Compound can be applied on vertical surfaces...

Read More »
Sealant targets pharmaceutical and medical applications.
Sealants

Sealant targets pharmaceutical and medical applications.

Extrusion coated onto various substrates such as film, foil, or paper, Allegro® M helps achieve clean peel. It seals to rigid cup or tray structures including HIPS, PVC, APET, PP, and HDPE. Allegro M helps lidding structures stand up to transport challenges, minimizing chance of compromise. Typical applications include unit-of-use liquid medications, diagnostic cartridges, pre-filled...

Read More »
Epoxy Adhesive is serviceable at temperatures down to 4°K.
Epoxies

Epoxy Adhesive is serviceable at temperatures down to 4°K.

With 3-minute set-up time, EP51M produces bonds with 2,000+ psi shear strength that exhibits resistance to thermal cycling and chemicals. Bonded parts can be safely handled within 30 min. Product, suited for cryogenic applications, adheres to metals, glass, ceramics, wood, vulcanized rubbers, and plastics. Insensitive to cleaning procedures, it can be used in electronic, electrical, computer,...

Read More »
Mortar

Wall Perimeter Sealer facilitates cove applications.

Featuring 100% solids formulation, chemical-resistant Superior Cove Kit is designed for vertical application at floor-wall joints to produce sanitary perimeter seal. This structural epoxy mortar, packaged in pre-measured kits to cover 35 lineal feet (4 in. vertical and 2 ft horizontal at 1/8 in.), requires clean surface prepared via sand blasting, water blasting, or other mechanical means. Each...

Read More »
Glass Sealant withstands temperatures to 1,450°F.
Coatings

Glass Sealant withstands temperatures to 1,450°F.

Aremco-Seal(TM) 617 is used to produce hermetic seals in porous ceramics and refractories in electrical and high-vacuum applications. Single-part, water-based glass coating, applied by dipping, brushing, or spraying, cleans up prior to curing with warm water. Curing is accomplished by setting at room temperature for 30 min and then heating to 1,600°F for 30 min. Odorless product contains no...

Read More »
Sealant acts as backup to field-applied caulking.
Sealants

Sealant acts as backup to field-applied caulking.

BACKERSEAL high-performance secondary sealant is designed for panelized wall systems, as well as concrete, brick, and stone structures. It consists of acrylic-impregnated cellular foam combined with laminations of closed-cell EVA foam. Non-staining sealant is compatible with wide range of caulking and substrate materials, and comes pre-compressed to smaller-than-joint-size with mounting adhesive...

Read More »
Tire Treads

Tires are manufactured with puncture sealing compound.

Unisteel G177 severe-service drive tires incorporate DuraSeal Technology, a gel-like, solvent-free compound built into inner liner of tire that seals punctures up to Â-¼ in. in tread area. Available in sizes 11R22.5 H, 11R24.5 H, and 12R22.5 H, tires also feature high-tear strength tread compound to help resist rubber chipping and chunking.

Read More »
Dow Corning® Z-2306 Silane Offers New Level of Concrete Protection
Sealants

Dow Corning® Z-2306 Silane Offers New Level of Concrete Protection

Midland, Mich. - August 25, 2006 - Dow Corning® Z-2306 Silane, a high-purity isobutyltriethoxysilane, can be used to formulate water repellent products that protect concrete structures from water absorption and chlorine ion ingress. When diluted with an appropriate solvent and applied properly, the Dow Corning Z-2306 Silane solution will penetrate and provide water repellence by chemically...

Read More »
Assembly Sealant provides instant adhesion.
Adhesives

Assembly Sealant provides instant adhesion.

Utilizing hot melt technology, HM-2510 combines crosslinked silicone sealant with instant green strength of pressure sensitive adhesive, meaning that parts can be moved immediately from one processing step to another. It offers aggressive adhesion to PVC, aluminum, painted and treated wood, paints, and plastics. Optimized for use with automated dispensing equipment, non-hazardous, low-odor...

Read More »

All Topics