Modules

System-on-Modules provide power and thermal management.

Based on IntelÂ-® PentiumÂ-® M processor and 855GME chipset, Plug-N-Run G3 System-on-Modules have controls that allow OEMs to build power and thermal protection schemes for extended time-between-recharging in mobile equipment. They also aid in careful management of performance vs. dissipation in high-density systems. Controls, accessible through BIOS setup, are used to configure operating...

Read More »
Plug-and-Play I/O Modules offer monitoring capabilities.

Plug-and-Play I/O Modules offer monitoring capabilities.

Power Meter 800 I/O modules are available in 2 models: PM8M2222 provides 2 digital outputs and inputs and 2 analog outputs and inputs, while PM8M26 provides 2 digital outputs and 6 digital inputs. By linking several analog and digital I/O inputs to one PM800 device, users can oversee transformer temperatures, generator fuel levels, equipment status, or usage of utilities such as water and steam.

Read More »
Interface Module is compatible with AS-i specification 2.1.

Interface Module is compatible with AS-i specification 2.1.

Model 750-655 AS-i Master network interface module allows seamless integration of AS-i bus protocol as sub-network to other bus protocols such as Ethernet, PROFIBUS, DeviceNet, and MODBUS. Housed in 12 mm wide package, unit can support up to 62 A/B slave devices and offers flexibility to wire network in star, line, branch, or tree configuration. It includes diagnostics to indicate errors, status...

Read More »
Modules convert fieldbus I/O into power I/O.

Modules convert fieldbus I/O into power I/O.

Power-I/O Modules convert network I/O, fieldbus I/O, DeviceNet(TM), Profibus(TM), or home automation I/O nodes into power switching nodes rated for 0.1-100 A. Din rail modules, rated 25-100 A, can be installed edge-to-edge on same din rail, without derating, for high-density installations starting at 25 A of switching capability every 30 mm. Some models include built-in, replaceable fuse. All...

Read More »
I/O Modules provide motion control.

I/O Modules provide motion control.

Models PXI-7352, PXI-7354, and PXI-7356 offer 2, 4 and 6-axis versions of stepper or servo motion controller. Each can be programmed using NI LabVIEW, NI LabWindows CVI, NI Measurement Studio for Microsoft Visual Basic, C and C++. Additional I/O include 8 total encoders, 64 bits discreet I/O, and eight 16-bit analog inputs. For applications requiring hardware-timed acquisition or signal...

Read More »

Module provides HART multi-drop communication.

Model MV156-HART provides 4 independent HART communication channels for Allen-Bradley's ControlLogix platform. HART channels generate signal to communicate in multi-drop mode enabling 2-way communication between processor and field transmitter. Module operates as master, supporting 15 instruments per channel with full configurable read/write access to instrument configuration/diagnostic tables....

Read More »

Modules connect processors to serial protocols.

In-chassis MV169 protocol conversion modules connect Allen-Bradley's 1769 CompactLogix processors with networks such as DF1, Modbus, ASCII, DNP 3.0, IEC60870, and C programmable. Modular solution provides backplane compatibility, 2 isolated serial ports with one debug port, and 57.6K baud rate. Serial ports allow connectivity to RS-232/422/485 devices and networks, enabling greater interface...

Read More »

Modules enable deployment of C applications.

Series MVI-ADM allows users to develop C applications that operate on Allen-Bradley's ControlLogix, PLC, SLC, and FLEX I/O platforms. Programmable units feature 3 serial ports, 2 of which are isolated for field interfaces supporting RS-232, RS-422, and RS-485. Two ports are jumper configured for direct or multi-drop field communication and 1 port is for module setup and diagnostics. Memory...

Read More »
Filtered Power-Entry Modules handle up to 20 A.

Filtered Power-Entry Modules handle up to 20 A.

Series EEJ features 20 A filter, attenuating 48 db at 30 Mhz in common mode for non-medical versions. Various terminations and installation types are available. Units have UL/CSA/VDE agency approvals and are suited for computer workstations, networking equipment, telecom-datacom equipment, medical devices, test and measurement devices, fitness equipment, and other industry applications.

Read More »
Wireless I/O System is housed in NEMA 4X enclosure.

Wireless I/O System is housed in NEMA 4X enclosure.

Housed in cast aluminum enclosure, N4ANT ruggedized wireless I/O transmitter/receiver system suits industrial, commercial, or general-purpose areas rated NEMA 4X. Aluminum enclosure is impact-resistant to UL requirements, and glass that protects antenna does not interfere with signal strength. Features include 1 W transmitter power, 4-20 mA analog signal, 3 contact outputs rated 120 Vac @ .05 A,...

Read More »

All Topics