Light Emitting Diodes (LED)

LED Driver can power three at a time.
Light Emitting Diodes (LED)

LED Driver can power three at a time.

S-8813 Series three-channel white LED driver IC can power up to 3 LEDs. S-881300OBPE-TB allows user to vary output current linearly between 5 and 18 mA by changing voltage supplied to current set pin (VISET). S-881300CPE-TB allows user to set output current between 5 and 18 mA by connecting resistor to current set pin (RISET). Ultra-small SON10 package and constant-current output make series...

Read More »
Bargraph LEDs are visible in sunlight.
Light Emitting Diodes (LED)

Bargraph LEDs are visible in sunlight.

Solid-state Linear Bargraph LEDs have average life span of 100,000+ hours. Standard intensity LEDs, with 565 to 660 nm at 20 mA, come in Ultra-Red, High-Efficiency Red, Yellow, and High-Efficiency Green. Super Intensity LEDs, with 523 to 330 nm at 20 mA, are available in Super Orange, Super Yellow, and Aqua Green. LEDs are suitable for aviation instrument panels, temperature gauges, automotive...

Read More »
LEDs are available in all colors and technologies.
Light Emitting Diodes (LED)

LEDs are available in all colors and technologies.

SML-LXR44 Series surface mount technology (SMT) LEDs produce 90° wide light beams oriented at right angles. Light output is parallel to circuit board. LEDs require circuit board space of 0.16 x 0.16 in., and are packaged on 12 mm taped reels. Devices can withstand up to 3 seconds at 260°C in reflow soldering operations. Typical output for 635 nm High-Intensity Red unit is 25 mcd with...

Read More »
Dual-Chip LEDs range in brightness from 660 to 470 nm.
Light Emitting Diodes (LED)

Dual-Chip LEDs range in brightness from 660 to 470 nm.

Series RAB362 right angle, single-level LED illuminators, for back- and edge-lighting applications, measure 0.362 in. long x 0.043 in. wide x 0.059 in. high. Bi-pin design aligns status indicators precisely. Available in Ultra Sunlight Visible and Standard Intensity versions, LEDs offer water-clear lenses and 120 deg angles. Average life span is 100,000+ hours. Solid-state design renders LEDs...

Read More »
LED Signal suits span wire or stationary arm applications.
Light Emitting Diodes (LED)

LED Signal suits span wire or stationary arm applications.

RX11 LED full ball signals are offered in 8 and 12 in. configurations, and feature expanded field-of-view. Design minimizes sun phantom effects, resulting in 70% reduced glare based on EN12368 standards. Power supplies can be individually adapted to accept characteristics of different controllers. They offer UV stabilized shells, moisture and dust resistant enclosures, and can retrofit into...

Read More »
Low-Profile LEDs provide high flux over wide angle.
Light Emitting Diodes (LED)

Low-Profile LEDs provide high flux over wide angle.

SuperFlux LEDs have water clear lenses and provide 7,000 mcd luminous intensity @70 mA current over 65 or 85 deg viewing angle, depending upon version. Measuring 7.62 mm sq. with 4.4 mm high body, through-hole LEDs can be mounted close together in clusters to fit wide variety of illumination applications in aviation, automotive, marine, industrial, and emergency signs. Colors include green,...

Read More »
Multiple Chip IRED provides total output power of 6.0 mW.
Light Emitting Diodes (LED)

Multiple Chip IRED provides total output power of 6.0 mW.

CLE400F-905 4-leaded device contains three 905 nanometer IRED chips mounted in flat leaded PLCC package. Chips feature current III-V solid state technology with transparent gallium aluminum arsenide windows. Chips are wire bonded in parallel and overcoated with clear epoxy, which provides emission angle of ± 70° at half power points. Maximum operating temperature with clear epoxy lens...

Read More »
Stacked LED Assembly retrofits to current set-ups.
Light Emitting Diodes (LED)

Stacked LED Assembly retrofits to current set-ups.

Multi-stack LED assembly allows custom configuration of LEDs stacked 1, 2, and 3 high, with spacing up to 6 in. wide, without special tooling. Operators can install from 6 to 36 LEDs at once in complex configurations. All LEDs have proper viewing angles, correct sequencing and polarity, and consistent color matching. Assembly also provides resistance to shock and vibration. It is made from UL...

Read More »
LED Light Pipe has thru-hole and surface mount versions.
Light Emitting Diodes (LED)

LED Light Pipe has thru-hole and surface mount versions.

Comprised of wide angle lens and flexible light pipe, FLP-O Series features oval shaped lens cap assembly with visible area of 0.125 in. (W) and 0.250 in. (L). Light pipe assembly provides capability for extending LED lighting to display and indicator panels up to 328.0 ft. Available Super-bright colors include Red, Green, Blue, Yellow and Amber; Ultra-bright colors include White, Blue, Turquoise...

Read More »
SMT LEDs provide indicator and display lighting.
Light Emitting Diodes (LED)

SMT LEDs provide indicator and display lighting.

1206 LEDs are sized 3mm overall, with die face of 1.5mm. They are available in green with typical wavelength of 560nm and light output ranging from 6.0 to 12.0 mcd; yellow with wavelengths of 580 and 570nm and light output of 6.0 to 12mcd; and red with wavelength of 660nm and 33.6mcd light output. Voltage ratings are 2.1V for green and yellow units, and 1.7V for red.

Read More »
Solder Redefined
Sponsored

Solder Redefined

Indium Corporation has developed a new twist on traditional solder by developing a composite with a reinforced matrix internal structure. The result is a solder with increased strength and reliability. Check out this video to learn more about the mechanics behind the groundbreaking technology.

Read More »

All Topics