Walter Adds Inserts to Walter Xpress Fast Delivery
Waukesha, WI—Walter has added indexable inserts to the range of products available via the Walter Xpress fast delivery service. Previously the special custom solutions available with Walter Xpress had been limited to round tools and tools that hold indexable inserts. Additionally, the tools were required to be “close to the standard tools.” Now, Walter offers its customers the benefits of...
Read More »
Seco Tools Introduces PCBN Inserts in New Grade Format and Geometries
The Polycrystalline Cubic Boron Nitride Inserts come in new long WL and short WS wiper radii and laser-etched chip breakers. The WL wiper inserts enable 100 percent feed-rate increase whereas the WS wiper insert’s cutting forces are reduced by 15 percent for enhanced machining in low-stability conditions. The CBN150 solid insert grade inserts deliver high-surface quality during light...
Read More »
New PCBN Inserts are Designed for Enhancing Hard Turning Operations
The Polycrystalline Cubic Boron Nitride Inserts are offered in long WL and short WS wiper radii. The CBN150 solid insert grade is designed for high surface finish quality in light interrupted and continuous cuts in hard turning operations. The inserts are available with laser-generated flowing-radii chipbreakers for smooth insert walls and few sharp corners.
Read More »
New A60/AG60 Cut MX Indexable Inserts are Designed for Small to Medium Pitch Threads
Walter’s A60/AG60 Walter Cut MX Indexable Grooving Inserts are designed for providing 60° partial-profile external threads in range of pitches 6-48 TPI—threads per inch. The units are offered with four cutting edges and are suitable for thread-turning in tight spaces. With its unique insert seat pockets, the inserts with different thicknesses can be used in same holder. Walter’s MX system...
Read More »
Metal Finishing Selection Guide
This unique chart compares different metal finishes by cost, corrosion resistance, applications and more.
Read More »
New Cermet WEP10 Indexable Turning Inserts Feature FP4 Soft-Cutting Geometry
Walter’s Cermet WEP10 Indexable Turning Inserts come with fine-grain titanium carbide substrate with Ni/Co binder. The unit’s FP4 geometry with edge preparation yields mirror finish surfaces at high or low cutting speeds. The WEP10 inserts are suitable for finishing operations for steels, stainless steels, and cast iron workpieces in metalworking, mechanical engineering, energy and automotive...
Read More »
New Ceramic Insert Grades are Designed for High Speed Turning Applications
Sandvik’s Ceramic Insert Grades are available in CC6220 and CC6230 models. Units are suitable for use on components made from HRSA materials. CC6230 RPGX inserts deliver cutting speeds up to 400 m/min during rough-turning operations and metal removal rate of 80 cm³/min. Units increase productivity of up to 50% than whisker ceramics and SiAlONs.
Read More »
Kennametal's New KBH10 Turning Inserts Offer Low Cutting Forces
KBH10 Polycrystalline Cubic Boron Nitride Turning Inserts are available in various geometries and edge preparations. Units are designed to deliver cutting speeds of 20% higher and provide surface roughness of Ra 0.2 and Rz 1. The Inserts are suitable for aerospace, automotive and power generation applications. KBH10 deliver a cutting speed of 180 m/min with average depth cut of 0.15 mm and...
Read More »
Walter's New Tiger∙tec® Gold Line Extension Tools Feature Latest Coating Technology for Long Tool Life
New Tiger∙tec® Gold Line Extensions are reliable and long lasting with a smooth rake face, gold-colored top layer, a tough cutting edge and the latest coating technology. The WKP35G milling grade tool is available in both positive and negative inserts. Inserts for the Walter BLAXX shoulder milling cutters include four 90° cutting edges. M4000 extensions feature a square shape and wavy design...
Read More »
WCK10 Ceramic Grades are wear-resistant.
WCK10 Si₃N₄ Ceramic Grade is designed for roughing gray cast iron at high speeds. Units come with negative chamfer and stable dimple clamping. These grades support both wet and dry machining. Units increase process reliability and tool life.
Read More »
Walter USA's Grooving Inserts provide more stable grooving operations.
Walter USA's Walter Cut GX34 double-edged grooving and parting inserts offer improvements in several areas. The inserts are clamped with screws which provide more stable grooving operations. They also offer an extra-long length of 1.34 in., making them ideal for large diameter workpieces and turret style machines. The inserts can be used in monoblock tools as well as grooving tools with a...
Read More »
Delivery Equipment That Really Delivers
Are you in need of safer, more efficient transportation equipment? Do you feel like your delivery equipment could really use an upgrade? Check out this video, and learn about Halo Ramp Company's patented safety platforms, and how they help you bypass your trickiest delivery challenges.
Read More »
