New Controls & Controllers Products

CMM Controller allows scanning speeds of 300+ mm/sec.

Universal CMM Controller, Model UCC allows CMMs to operate in standard touch-trigger mode, digitizing mode with analog probes, and full high-speed scanning mode. Axis-blending software can move CMM in 3 axes at once, allowing true circular motion to accommodate irregular part contours and geometries. Lost Surface Recovery capability automatically relocates scanning probe to last known good point,...

Touch Panels operate and monitor small machines.

Operating in portrait or landscape orientation, Simatic TP 177 A and TP 177micro are equipped with 5.7 in. touch display, with 320 x 240 pixel resolution. Model TP 177 A features onboard Profibus interface for connection to Simatic-S7 controller. Model TP177micro is point-to-point connected to Simatic S7-200 mini PLC and interfaces with PPI networks per multi-master communications. Both feature...

User Interface facilitates NC programming.

SmarT.NC guides users in self-explanatory and intuitive way through complete NC programming tasks by using straightforward forms. Operator can decide whether to use interface or plain language level at any time. If program has been created with smarT.NC, it can still be edited with plain language editor. In addition to integrated pattern generator, system enables program verification and...

Variable Frequency Drives offer NEMA 3R mounting option.

NEMA 3R enclosure on Series SED2 allows outdoor mounting of drives near controlled mechanical equipment and permits short motor lead lengths. Package is equipped with main input fused disconnect and optional 2- or 3- contactor bypass and line reactor. Shield protects unit from heating effects of indirect sunlight. Filtered inlet, fan-controlled exhaust, and thermostatically controlled heater...

How Manufacturing Automation Can Reduce Workplace Injuries and Improve Morale

To learn more about how automation can solve your workplace issues, download the full white paper.

Stepper Motor Controller has 2 limit switches per axis.

Available in single- and 3-axis configurations, Stepper Motor Controller Card for PCI bus controls and supports all parameters of bipolar stepper motor, including velocity, acceleration, deceleration, amount of steps, and direction. Card supports 3 synchronization modes and step division up to 1/8 steps. Two end switches and rotation switch that operates in 2 modes can be connected to controller.

Telecom Blade has 1 GHz processor and PICMG 2.16 interface.

Katana(TM)752i is equipped with PowerPCÃ-® 750GX processor and Marvell Discovery III system controller. Configurable cPSB blade features 2 PTMC sites, 4 Gigabit Ethernet channels, multi-level cache, and CTBus/H.110 interconnect that enables product to acquire and process both TDM and packet data. PTMC sites support 32-bit PCI data transfers at 33 or 66 MHz and feature dedicated CTBus and RMII...

Microcontroller Board features radio link.

Model WMB-USA uses Atmega8535-16 chip, running at 16 MHz and achieving almost 16 MIPS. Built-in serial RF link has variable power from 1-10 mW with selectable data speeds. Suited for wireless control, mobile robots, and data-logging applications, board accepts input voltage from 6-35 V with polarity inversion protection, and includes four 8-bit I/O ports and one serial port. It measures 84 x 70 x...

Motorized Rotation Stage provides 360-

General-purpose 8MR180 has 2 in. aperture in middle, and coarse angular position is indicated on 360Ã-

Process Control monitors air usage of atomizers.

Utilizing closed-loop module, AirTronic provides continuous, precise monitoring and control of air volume set points for rotary atomizers, air atomizers, and powder pumps. It accommodates independent and slave modes by incorporating 2 channels per module and 2 modes of operation. AirTronic provides production monitoring through standard lpm display units at module or remote location. It offers...

Fire Protection System provides pre-wired/piped solution.

MCC (Mist Control Center) AquaMist Delivery System is pump skid assembly with pump, controller, control valves, deluge valve, control panel, and system strainer. System also incorporates AquaMistÃ-® fire protection system, which uses mist application nozzles that produce reduced droplet sizes in discharge pattern. In fire condition, fine mist is transformed to steam, expanding each water...

Precision Machined Parts for High Tech Applications

For precision and value that sets the standard for quality and craftsmanship, EGS Production Machining is the source for precision and value. Our extensive capabilities and dedication to customer service allow us to deliver the optimal manufacturing solution. See our video to learn more.