Vibration Analyzer/Balancer suits blowers and grinders.
Model 222-D portable vibration signature profiler, analyzer, and 2-plane dynamic balancing instrument can identify unbalance, resonance, mechanical looseness, and bad bearings. Corrective actions are recorded via prints made before and after vibration signatures. Model 222-D is suitable for rotating machines, and can also be used to dynamically balance fans, shafts, rotors, impellers, spindles,...
Read More »Mechanical Analyzer monitors viscoelastic materials.
DMA Q800 Dynamic Mechanical Analyzer makes mechanical stress/strain measurements at temperatures from -150 to 600 deg C. It has non-contact, linear motor for precise stress control, low-friction air bearings, and optical encoder for strain detection. Sample clamps are available for operation in cantilever, 3-point bend, shear, compression and tension modes of deformation. Submersion clamps also...
Read More »
Power Quality Analyzer offers intelligent download.
PA-9Plus provides 12 megabytes of internal storage, on-board auxiliary power input capabilities, and optional removable flash memory card. Metrosoft AVO PA-9W software enables unit to trend imbalance, individual harmonics, THD and TDD, and preview and download only what is required. Chart analysis is simplified through zoom/unzoom capabilities. PA-9Plus complies with all applicable IEC, IEEE and...
Read More »
Torque Analyzer offers RS-232 port for direct downloading.
TorqueMate Plus torque analyzer offers 5Vdc capability to interface with brushless rotary transducers. Software allows selection of 3 different Low-Pass filters, and identifies correct range of any smart-enabled transducers. Torque measurement includes lbs/ft, lbs/in., oz/in., and kg/m. When connected to transducer, accuracy exceeds +/- 0.25% full scale. Memory stores calibration for 15 different...
Read More »
Gauge Application Guide
This white paper provides a gauge application guide to help you in selecting the right gauge for your needs.
Read More »
Residual Gas Analyzer industrial coating applications.
Prisma 80 residual gas analyzer and leak detector monitors gases in vacuum coating system to ensure that correct vacuum conditions exist. It has 32-bit operating system with TalkStarÃ-® software for setup and configuration. Multiscan windows permit simultaneously displaying screens of wide-ranging scans or focusing in on key components. Design features include integrated total pressure...
Read More »
Spectrum Analyzer is portable and programmable.
Hand-held, battery operated Model 401B Personal Spectrum Analyzer comes with calibrated E-Field and H-Field probes, broadband active antenna, and high gain preamplifier to make EMC Pre-Compliance measurements simple and straightforward. Limit lines for FCC Part 15A/B, CISPR 11A/B, and CISPR 22A/B are stored internally. Applications include checking information technology, scientific, and...
Read More »
Thermal Imaging System has accuracy to 2 degrees C.
Stinger Thermal Imaging System offers uncooled Focal Plain Array (FPA) 320 x 240 sensor, and provides on-line, radiometric thermal imaging. Real-time video captures data from up to 50 areas of interests at rates up to 60 frames per second. Test and playback features allow data to be captured, stored as image files, or exported. System includes Stinger camera with focusing lens, WindowsÃ-®...
Read More »
Portable Analyzer measures oxygen in air and water.
Digital LCD Oxygen Analyzer uses galvanic sensor to measure percent oxygen in air and ppm of dissolved oxygen in aqueous solutions, with accuracy of +/-5.0% saturation and +/-0.2 ppm, and precision of 0.1%. It is temperature compensated for air calibration and follows Henry's Law for indication of ppm dissolved oxygen. Oxygen sensor is maintenance free, does not require membrane replacements, and...
Read More »Filter Wheel tests NIR analyzers.
Filter Wheel performs tests on wavelength, linearity, and noise to verify that near-infrared analyzer instruments are in compliance with NIR spectroscopy standards. Software leads user through 2-3 min test process. Tests run individually or as suite, and users can view individual results during test, or view overall results once tests are complete. Filter wheel maintains log of past results,...
Read More »
Simple Gas Determinator can be ramped for gas separation.
Model TCH600 Nitrogen/Oxygen/Hydrogen (N/O/H) Determinator delivers N/O/H determination in 1 analysis for metal and inorganic applications. It offers re-engineered solid-state infrared (IR) and thermal conductivity (TC) detectors, dynamic flow compensation, and electrode impulse furnace. Its WindowsÃ-®-based operating system offers diagnostics, archiving, and flexible reporting capabilities....
Read More »
Standex Engraving Mold-Tech Offers Nickel Shell Capabilities on a Global Scale
Standex Engraving Mold-Tech is the premier, global supplier for mold texturing and surface finishing. With a full range of services, Standex Engraving Mold-Tech is also the only nickel shell supplier producing in three global locations. See our video to learn more.
Read More »
