Logarithmic Amplifier is suited for signal compression.
Designed to amplify photodiode signals from fiber optic cables in ONET, Model LOG114 operates on single +5 or Ã-
Read More »Current Sense Amplifier resolves signals up to 36 V.
Model LT6106 features maximum 250 mV input offset voltage, full-scale differential input of 500 mV, and dynamic range of 2000:1. For handling fault conditions, LT6106 can withstand common mode voltages up to 44 V and responds to signal changes within 3.5 Ã-µsec. Operates at temperatures between -40Ã-
Read More »Anadigics' Advanced Power Amplifiers Support Qualcomm's HSPA Solutions
ANADIGICS' Power Amplifiers Selected for MSM7200 HSUPA and MSM6280 HSDPA Reference Designs from QUALCOMM WARREN, N.J., Dec. 4 /- ANADIGICS, Inc. (NASDAQ:ANAD), a leading supplier of wireless and broadband solutions, today announced that the Company's WCDMA and GPRS/EDGE power amplifiers (PAs) have been specified by QUALCOMM for the Mobile Station Modem(TM) (MSM(TM)) MSM7200(TM) and MSM6280(TM)...
Read More »Amplifier targets portable audio applications.
Charge pump-based DirectPath(TM) TPA6130A2 features power supply rejection ratio of 109 dB, quiescent current of 4 mA, differential stereo inputs, and 64-step software-based volume control. Providing direct path between amplifier and speaker eliminates need for large, dc blocking capacitors. Depop circuitry suppresses pop noise to inaudible level, and wide voltage rail of 2.5-5.5 V enables...
Read More »Elastomer Shlastomer, Right? Selecting the Right Elastomer for Your Sealing Boots and Fasteners
Different elastomer formulations affect your parts' physical properties, functions, and service life. Therefore, it's important to test a few different elastomers, when assembling your product, to determine the best one for your needs.
Read More »Power Amplifiers target point-to-point radios.
Covering radio frequency bands from 2.5-19.7 GHz, MAAPGM00XX-DIE Amplifiers produce power levels from 1-2 W with third order intercept points from 38 to 44 dBm. Units feature gain up to 34 dB and flatness of less than Ã-
Read More »Amplifiers optimize distortion power and noise performance.
Integrating precision gain-setting resistors on-chip, Model LT6402 and LT6411 differential amplifiers can be used as high-speed ADC drivers, twisted-pair line drivers, and single-ended to differential signal converters. Model LT6402 has -3 dB bandwidth of 300 MHz, and is available in 6, 12, and 20 dB fixed gain options. With -3 dB bandwidth of 650 MHz and slew rate of 3,300 V/Ã-µs, Model...
Read More »Audio Amplifiers deliver 1.3 W continuous average power.
Suited for cell phones and PDAs, Models NCP2892 and NCP2990 produce zero pop-and-click noise with differential and single-ended audio inputs, respectively. Audio power amplifiers offer turn-on time down to 15-30 msec and can be connected directly to battery. Using 1 Ã-µF bypass capacitor, NCP2892/990 offer 100 and 60 msec wake up times. Devices feature 10 nA current shutdown mode, 2.2-5.5 V...
Read More »TWT Amplifiers suit high output power applications.
Providing RF power to test and measurement, industrial and university research and development, and service applications, Models 125T18G26 and 125T26G40 deliver 125 W CW power in frequency ranges of 18-26.5 GHz and 26.5-40 GHz respectively. Both TWTs include built-in IEEE-4888 (GPIB) interface, 0 dBm input, VSWR protection, gain control, RF output sample port, auto sleep, monitoring of TWT helix...
Read More »Op Amps target high-voltage industrial market.
Achieving 1.1 nV/rtHz voltage noise and 80 MHz gain bandwidth with 3.6 mA supply current, Model OPA211 bipolar-input op amp provides 100 Ã-µV offset voltage and 0.2 Ã-µV/Ã-
Read More »Ultra-Low Noise Amplifiers cover microwave frequency bands.
Offered in 20+ models, ultra-low noise JCA Amplifiers can be employed in narrowband situations, such as GPS receiver, or in electronic surveillance system where several octaves of bandwidth may be necessary. Narrowband models can be optimized for sub 0.5 dB noise figures over 100-200 MHz sub-bands, and broadband multi-octave noise figure performance is rated under 1 dB max for C-Band frequencies...
Read More »5 and 13 Micron Resolve Columns with Greater Bed Stability
Jordi Labs provides materials solutions that set the standard for innovation and quality. Our line of GPC and GFC columns are on the cutting edge of precision manufacturing and a result of our uncompromising commitment to quality and customer service. See our video to learn more.
Read More »