Aremco Products, Inc.

High-Temperature Coating protects structures against corrosion.
Paints & Coatings

High-Temperature Coating protects structures against corrosion.

UsedÂ- in ambient temperatures up to 1,100°F, Corr-Paint™ CP4060 provides corrosion protection and color identification for aluminum and cast steel structures. Single-part, red-pigmented, silicone-based, water-dispersible coating adheres to sandblasted as well as marginally prepared metal surfaces and dries at room temperature. Product cures as coated...

Read More »
Ceramic Adhesive bonds thermocouples to high-temp heater.
Adhesives & Sealants

Ceramic Adhesive bonds thermocouples to high-temp heater.

Ceramabond™ 571 consists of water-based, 2-part (powder and liquid), magnesium oxide-filled ceramic adhesive and coating used to bond thermocouples to molybdenum-rhenium heater tubes for applications to 3,200°F. While electrical properties include volume resistivity of 109 ohm-cm and dielectric strength of 255 V/mil, mechanical properties include tensile shear strength of 500 psi and...

Read More »
Alumina Ceramic molds high-temperature components.
Chemicals & Gases

Alumina Ceramic molds high-temperature components.

Consisting of full-fired, 99% pure alumina ceramic, Aremcolox™ 502-1400-99 provides abrasion and corrosion resistance as well as mechanical strength and electrical resistance for continuous operating temperatures to 3,000°F. Product features compressive strength of 340,000 psi, flexural strength of 46,000 psi, and dielectric strength of 225 V/mil. Typical applications include burner...

Read More »
High-Temperature Sealant suits applications to 950°F.
Adhesives & Sealants

High-Temperature Sealant suits applications to 950°F.

Formulated by combining high-temperature resin with ceramic fibers and powders, Pyro-Putty™ 950 can be used as gasketing compound for boilers, compressors, heat exchangers, furnaces, ovens, and exhaust manifolds. Product repairs rough, scored, or irregular surfaces and is resistant to chemical and steam attack, high pressure/vacuum atmospheres, mechanical vibration, and joint movement. Offered...

Read More »
Epoxy Potting Compound suits applications to 365°F.
Adhesives & Sealants

Epoxy Potting Compound suits applications to 365°F.

Offering thermal conductivity, electrical insulation, and low shrinkage after cure, Aremco-Bond™ 2315 is suited for potting and encapsulating densely packaged power supplies, rectifiers, ICs, oscillators, DACs, amplifiers, and relays. Black-pigmented product provides flexural strength of 12,300 psi and dielectric strength of 480 V/mil. Mixed in ratio of 100 parts resin to 25 parts hardener by...

Read More »
High-Temp Corrosion-Resistant Coating enhances motor housings.
Paints & Coatings

High-Temp Corrosion-Resistant Coating enhances motor housings.

Used to coat steel motor housings in applications to 400°F, Corr-Paint™ CP2000 dries and cures at room temperature to hard, non-porous, abrasion-resistant surface. Single-part polymeric coating, resistant to acids, also survives salt fog, salt spray, and humidity testing periods of 1,000+ hr. Typically applied in 4.0 mil wet film thickness that dries to ~2.0 mil, coating has 200–240 cP...

Read More »
Thermoplastic Adhesive suits temporary mounting applications.
Adhesives & Sealants

Thermoplastic Adhesive suits temporary mounting applications.

AdheringÂ- to ceramics, glasses, and metals, Crystalbond™ 509 is suitable for temporarily mounting substrates that require dicing, grinding, or polishing operations. Thermoplastic adhesive is applied by preheating mounting plate to 250°F, melting and spreading adhesive in uniform layer, then positioning part over adhesive, allowing entire assembly to cool. After processing,...

Read More »
Black-Body Coating formulated for metal surfaces such as stainless steel
Paints & Coatings

Black-Body Coating formulated for metal surfaces such as stainless steel

Demonstrating emissivity greater than 0.90 at temperatures to 2,000°F, HiE-Coat™ 840-M has been formulated for metal surfaces such as stainless steel. Jet-black, water-dispersed, ceramic coating is used for gas-fired burners to optimize thermal efficiency of commercial and consumer appliances, industrial ovens, and furnaces. Applied by sponge brush, roller, or spray equipment, VOC-free...

Read More »
Ultra-Temp 516 Bonds Zirconia Ceramics
Adhesives & Sealants

Ultra-Temp 516 Bonds Zirconia Ceramics

Summary Ultra-Temp™ 516, a high temperature zirconia and zirconium silicate filled adhesive manufactured by Aremco Products, Inc., is now used to bond zirconia ceramics used in applications to 3200 Â-ºF (1760 ºC). Features Ultra-Temp™ 516 is a new, single part, zirconia and zirconium silicate filled, inorganic adhesive system for bonding zirconia components used in high...

Read More »
Machinable Glass-Ceramic withstands temperatures to 1,100°F.
Machinery & Machining Tools

Machinable Glass-Ceramic withstands temperatures to 1,100°F.

Optimized for machinability using carbide tools, Aremcolox™ 502-600 is suited for use in high vacuum and electrical and electronic high temperature applications.Â- Properties include respective compressive and flexural strengths of 32,000 and 14,000 psi, dielectric strength of 380 V/mil, dielectric constant of 6.8 @ 1 MHz, and thermal conductivity of 4.08 Btu-in/hr-ft²-°F....

Read More »
High-Temperature Coating protects structures against corrosion.
Paints & Coatings

High-Temperature Coating protects structures against corrosion.

UsedÂ- in ambient temperatures up to 1,100°F, Corr-Paint™ CP4060 provides corrosion protection and color identification for aluminum and cast steel structures. Single-part, red-pigmented, silicone-based, water-dispersible coating adheres to sandblasted as well as marginally prepared metal surfaces and dries at room temperature. Product cures as coated...

Read More »
Ceramic Adhesive bonds thermocouples to high-temp heater.
Adhesives & Sealants

Ceramic Adhesive bonds thermocouples to high-temp heater.

Ceramabond™ 571 consists of water-based, 2-part (powder and liquid), magnesium oxide-filled ceramic adhesive and coating used to bond thermocouples to molybdenum-rhenium heater tubes for applications to 3,200°F. While electrical properties include volume resistivity of 109 ohm-cm and dielectric strength of 255 V/mil, mechanical properties include tensile shear strength of 500 psi and...

Read More »
Alumina Ceramic molds high-temperature components.
Chemicals & Gases

Alumina Ceramic molds high-temperature components.

Consisting of full-fired, 99% pure alumina ceramic, Aremcolox™ 502-1400-99 provides abrasion and corrosion resistance as well as mechanical strength and electrical resistance for continuous operating temperatures to 3,000°F. Product features compressive strength of 340,000 psi, flexural strength of 46,000 psi, and dielectric strength of 225 V/mil. Typical applications include burner...

Read More »
High-Temperature Sealant suits applications to 950°F.
Adhesives & Sealants

High-Temperature Sealant suits applications to 950°F.

Formulated by combining high-temperature resin with ceramic fibers and powders, Pyro-Putty™ 950 can be used as gasketing compound for boilers, compressors, heat exchangers, furnaces, ovens, and exhaust manifolds. Product repairs rough, scored, or irregular surfaces and is resistant to chemical and steam attack, high pressure/vacuum atmospheres, mechanical vibration, and joint movement. Offered...

Read More »
Epoxy Potting Compound suits applications to 365°F.
Adhesives & Sealants

Epoxy Potting Compound suits applications to 365°F.

Offering thermal conductivity, electrical insulation, and low shrinkage after cure, Aremco-Bond™ 2315 is suited for potting and encapsulating densely packaged power supplies, rectifiers, ICs, oscillators, DACs, amplifiers, and relays. Black-pigmented product provides flexural strength of 12,300 psi and dielectric strength of 480 V/mil. Mixed in ratio of 100 parts resin to 25 parts hardener by...

Read More »
High-Temp Corrosion-Resistant Coating enhances motor housings.
Paints & Coatings

High-Temp Corrosion-Resistant Coating enhances motor housings.

Used to coat steel motor housings in applications to 400°F, Corr-Paint™ CP2000 dries and cures at room temperature to hard, non-porous, abrasion-resistant surface. Single-part polymeric coating, resistant to acids, also survives salt fog, salt spray, and humidity testing periods of 1,000+ hr. Typically applied in 4.0 mil wet film thickness that dries to ~2.0 mil, coating has 200–240 cP...

Read More »
Thermoplastic Adhesive suits temporary mounting applications.
Adhesives & Sealants

Thermoplastic Adhesive suits temporary mounting applications.

AdheringÂ- to ceramics, glasses, and metals, Crystalbond™ 509 is suitable for temporarily mounting substrates that require dicing, grinding, or polishing operations. Thermoplastic adhesive is applied by preheating mounting plate to 250°F, melting and spreading adhesive in uniform layer, then positioning part over adhesive, allowing entire assembly to cool. After processing,...

Read More »
Black-Body Coating formulated for metal surfaces such as stainless steel
Paints & Coatings

Black-Body Coating formulated for metal surfaces such as stainless steel

Demonstrating emissivity greater than 0.90 at temperatures to 2,000°F, HiE-Coat™ 840-M has been formulated for metal surfaces such as stainless steel. Jet-black, water-dispersed, ceramic coating is used for gas-fired burners to optimize thermal efficiency of commercial and consumer appliances, industrial ovens, and furnaces. Applied by sponge brush, roller, or spray equipment, VOC-free...

Read More »
Ultra-Temp 516 Bonds Zirconia Ceramics
Adhesives & Sealants

Ultra-Temp 516 Bonds Zirconia Ceramics

Summary Ultra-Temp™ 516, a high temperature zirconia and zirconium silicate filled adhesive manufactured by Aremco Products, Inc., is now used to bond zirconia ceramics used in applications to 3200 Â-ºF (1760 ºC). Features Ultra-Temp™ 516 is a new, single part, zirconia and zirconium silicate filled, inorganic adhesive system for bonding zirconia components used in high...

Read More »
Machinable Glass-Ceramic withstands temperatures to 1,100°F.
Machinery & Machining Tools

Machinable Glass-Ceramic withstands temperatures to 1,100°F.

Optimized for machinability using carbide tools, Aremcolox™ 502-600 is suited for use in high vacuum and electrical and electronic high temperature applications.Â- Properties include respective compressive and flexural strengths of 32,000 and 14,000 psi, dielectric strength of 380 V/mil, dielectric constant of 6.8 @ 1 MHz, and thermal conductivity of 4.08 Btu-in/hr-ft²-°F....

Read More »

All Topics