Kennametal Inc.
Suite 3300
Pittsburgh, PA 15219
Coated Carbide Grades turn cast and ductile irons.
Grade KC9325, suited for gray cast and nodular irons, performs under interrupted cut conditions, and Grade KC9315, suited for use with ductile irons, employs coating that resists flank wear. Both grades reduce production time without any reduction in tool life. Grade KC9325 has MTCVD TiCN coating and fine grain aluminum oxide coating layer for total thickness of 16 microns, while Grade KC9315 has...
Read More »
Sialon Grade meets performance of whisker ceramics.
Kyon 1540 sialon (silicon nitride/aluminum oxide/aluminum nitride) ceramic grade handles roughing through finishing processes on cobalt-, iron-, and nickel-based high-temperature alloys. Formulated from 30% alpha and 70% beta sialon, product is offered in round, square, diamond, and triangle negative insert geometries as well as v-bottom round positive insert geometries. Styles are also available...
Read More »
Tooling suits integrated turning and milling machines.
Equipped with Kenclamp clamping system, KM tooling delivers 3-surface contact. Quick-change tooling system consists of spindle with built-in KM connection that accepts KM toolholder or cutting unit using face and taper contact between spindle and toolholder. Machine-specific adaptors make it possible to utilize full line of existing KM turning tools on any machine. Line includes collet and...
Read More »
Carbide Drills handle high-silicon aluminum and difficult cuts.
Sculptured Edge (SE) 256 drills, with 2 margins per flute, are suitable for irregular exits, cross-holes, and interrupted cuts. Diameters range from .1563-.7580 in. and 5-16 mm in Grade KC7015. Type SE 731 and SE 732 drill and chamfer in one pass prior to tapping. They are offered in tap sizes from 8-32 to 7/8-14, in cutting depths of 3 and 4 times diameter, and apply 45Ã-
Read More »
Carbide End Mills cut ferrous, high temperature, and titanium alloys.
Multi-layer TiAlN/TiN/TiAlN-coated carbide grade KC633M offers resistance to wear and deformation when rough machining ferrous materials and high-temperature alloys. Multi-layer TiN/TiCN/TiC-coated grade KC625M is suited for non-ferrous materials, while KC635M TiAlN-coated material suits high-temperature alloys. Other grades include KP525M powdered-metal material, KH110M uncoated steel grade with...
Read More »
Tooling System accommodates Swiss-style machines.
KM Micro quick-change tooling system reduces time required to change inserts from 5 min to 30 sec. Based on KM quick-change tooling design, system consists of 1 clamping unit attached to gang plate. Clamping unit locks toolholder that uses coincidental cone arrangement to provide 3-point contact between clamping unit and toolholder. Clamping units are available to fit 12 and 16 mm and 1/2 and 5/8...
Read More »
Carbide Drills avoid bending thin-wall alloy parts.
Sculptured Edge (SE) 284 and SE 285 drills have positive-rake chisel point with large active cutting area that reduces stress and provides freer chip flow when machining high-temperature alloys. Cutting geometry reduces thrust by 20%. Short-length SE 284 models are offered in metric sizes from 4 to 25 mm and inch sizes from .1563 to .7500 in. SE 285 drills are regular length by DIN standards....
Read More »Face Mills offer high rake angles for longer tool life.
KSSM face mills include 0, 15, and 45Ã-
Read More »
Cutters and Inserts handle heat resistant alloys.
Made with ceramic grade Kyon 2100, cutters work at speeds of 3000 sfm to rough mill nickel, cobalt, and iron based heat resistant alloys. Cutters and inserts also machine Waspalloy, Haynes 25, Inconel 718, Stellite and similar materials at cutting speeds of 2000 to 4500 sfm and feed rates of 0.002 to 0.005 ipt. Also available are KC9110 and KC9125 inserts, both with 3 coating layers: TiCN,...
Read More »