Aprima Medical Software, Inc
Carrollton, TX 75006
Share:
Color Camera outputs precise and detailed RGB signals.
Model IK-TF1 offers 3CCD micro prism system, C-Mount, and 10 lux sensitivity. One-piece camera provides 570 lines of resolution and 64 dB signal-to-noise ratio. Co-Site Sampling arrangement of its three 1/3 in., 410,000 pixel IT-CCDs results in capture of computer-ready color images and reduced smear. Functions include 9-step electronic shutter system (1/60 to 1/50,000 sec), automatic and manual...
Read More »
Interface Converters work with RS232, RS422 and RS485.
Models IC485+ and IC485+I allow standard RS232 port to communicate with individual RS422 device or with multiple devices within RS485 network. Both devices support RS422 full duplex mode as well as RS485 full or half duplex master and slave modes. Onboard LEDs indicate that device is properly powered and when device is transmitting and receiving. Six-position screw terminal block on board...
Read More »
Computer Chassis holds 8 CompactPCI cards.
MaxAir.10 7U tabletop or rack-mount microchassis is made of powder coated aluminum, has stainless steel hardware, and weighs 19 lb. Extruded aluminum cardguide maximizes airflow between slot positions and accepts standard 0.062 in. cards. Vented top and bottom EMI covers are zinc plated steel. Front plug-in power supplies provide CPCI voltages of +5, +3.3, +12 and -12. Output power ranges from...
Read More »
Bulk Liquid Dispenser replaces 55 gal drums.
Tote-A-Lube system replaces 55 gal drums with clean, stackable, and systemized storage and bulk liquid dispensing system. Made of high-density polyethylene plastic with corrugated V-groove sidewalls, 70 and 120 gal tanks can hold 20,000 lb of pressure exerted on top. Tanks have top outer grooves that interlock with bottom inner grooves to secure tanks in place, allowing tanks to be stacked 3...
Read More »
Parts Cleaning System takes parts through on conveyor belt.
PWD Series parts washer/dryer system has single conveyor belt that links washing and drying components with optional rinsing, rust-inhibiting, moisture blow-off and liquid filtration equipment. Standard unit is 12.5 ft long and 45 in. wide, with 180 gal cleaning solution tank and V-jet spray nozzles on top, bottom and sides of wash chamber. Modular systems can be built with varying belt widths,...
Read More »
PCB Connectors suit GPS applications.
RTI-8300-04 right angle, MCX, female, surface mount PCB connector is suitable for 50 ohm applications with frequencies up to 6 Ghz. Snap-on mating provides rapid connects and disconnects. RMX-8300-04 offers gold plated machined brass body, gold plated contact, and TeflonÃ-® insulation. Suitable for space and weight-limited design criteria, MCX connectors are 30% smaller than SMB connectors,...
Read More »
Wire Wound Chip Inductors have dim. tolerance of -
LQ-LBH Series chip inductors reduce EMI, and enable mounting density with pitch of 0.3mm, Q-Values of 12-46, and non-directional surface-mountability. LQ-LBH devices provide 100% silver wire wound (Ag) internal conductors and advanced ceramics. Inductance range is from 2.7 to 100 nH, maximum current is rated from 200mA to 1A, and DC resistance values range from 0.03 to 1.0 Ohms.
Read More »
Solids Reduction Unit retrofits to twin shaft grinders.
Annihilator twin shaft solids reduction unit is supplied with seals and bearings housed in replaceable stainless steel cartridge, which allows on-site replacement. Counter-rotating, hexagonal shaft design coupled with hardened steel cutters provide maximum shredding strength necessary to process 300 to 4,250 GPM of influent. Annihilator is fitted with toothed cutting spacers, electronic control...
Read More »
Dust Collector occupies 10 sq ft of shop space.
Model 2.3x3S/D multi-function smoke and dust collector collects smoke from welding operation, converts to downdraft bench for finishing operations, and can be fitted with duct wye and blast gate to collect dust from metalworking operations. Its 3 hp blower moves 1,500 CFM of air. Collector also offers high-efficiency permanent fabric filter and removable dust pan. Options include activated carbon...
Read More »
Battery Monitor checks float current.
Float Charging Current Probe (FCCP) monitors float charging current on up to 2 strings of VRLA batteries. Non-intrusive sensor is easy to install in new and existing applications. It monitors internal current changes in batteries over time and allows sufficient duration to react prior to possible catastrophic event.
Read More »