Aprima Medical Software, Inc
Carrollton, TX 75006
Share:
Soil Sampler grabs samples and catches cores.
Piston Sampler collects discrete interval samples in difficult conditions, such as flowing/heaving sands and swelling clays using any direct push system. System also works in soils below groundwater, and prevents liner failure during sample collection. Using either or both of 2 core catcher options can minimize chance of losing soil sample.
Read More »Powder Coat Finish is environmentally friendly.
SpectraShield powder coating finish is applied to components of rolling doors and rolling counter doors. It provides color retention, UV stability, and resistance to corrosion, chemicals and abrasion. Its total palette consists of more than 200 colors. SpectraShield gray powder coating is used on all of company's exposed steel door surfaces including guides, bottom bar, and endplate brackets.
Read More »Assembly Platform maximizes production efficiency.
Linear motor driven CHADIQh-1 odd-form, final assembly and photonics assembly platform has footprint of less than 1 meter. It is capable of handling virtually all off-form through-hole and surface mount applications along with fully automatic device assembly applications.
Read More »MOSFETs are housed in TO-220 packages.
Models IXTP01N100D and IXTP02N05D high voltage depletion mode MOSFETs are normally on at 0V gate bias and require -5V gate bias to block current. Model IXTP01N100D is rated 1000V/100mA with 110 Ohm RDS(on) at VGS = 0V while IXTP02N05D is rated 500V/200mA and has RDS(ON) of 30 Ohms. Both are housed in TO-220 package for 25W at TC=25 deg C power dissipation. Applications include current regulators,...
Read More »MOSFETs have high voltage depletion mode.
IXTP01N100D and IXTP02N50D MOSFETS are normally on at 0V gate bias and require negative gate bias to block current. IXTP01N100D is 1000V/100mA rated MOSFET with 110 ohm RDS(on) at VGS=0V, while IXTP02N50D is rated at 500V/200mA with RDS(on) of 30 ohms. Both devices are housed in TO-220 package allowing for high power dissipation. Applications include level shifters, current regulators, normally...
Read More »Digital to Synchro Converters handle high temperatures.
Model DSPL60 requires 115V 60Hz reference input and +5 Vdc @ 20ma. Converters accept 14 bit natural binary angle and convert it into 3-wire synchro signal. Output is short circuit proof, and current limited with transient protection and thermal cutoff. Devices measure 2.6 x 3.1 x 0.51 in. and have thermally conductive encapsulant and metal top plate. Operating temperatures are 0-70 or -55 to 90...
Read More »Reed Relay has >10E+14 ohms insulation resistance.
Low-profile CR-Series leadless 50 Ohm reed relay switches at speeds up to 6 GHz with less than 40 ps rise times. To eliminate potential packaging stress, it is made with ceramic case that matches thermal coefficient of expansion of reed switch glass and reed lead. Capable of withstanding reflow soldering operations up to 260 deg C, it uses no internal solder, and has 1 microV typical thermal...
Read More »Rotary Encoder Collar can be used to sense shaft speeds.
Aluminum clamp-type collars can be configured with metallic targets to permit shaft speed sensing. Metallic targets can be read by customer-supplier variable reluctance sensors. Collars are unaffected by oils and coolants, and smooth bore will not damage shafts. They are available in one- and two-piece clamp-type designs with bore sizes from 1/2 in. and ODs up to 12 in. Applications include...
Read More »Handles are available in many styles and sizes.
Aluminum, brass and stainless steel handles match standard panel heights such as 3 1/2, 5 1/4, 6, 7, and 8 in. They are available in extruded, positive locking, folding and standard square, oval and wire types. All are distinguished by parallelism and consistent center-to-center measurements. Bar-type handles are available with tape inserts and 2, 3 or 4 legs.
Read More »Broach Set cuts keyways in 9 bore sizes.
Minute Man No. 10 Set consists of high speed steel broaches, bushings and necessary shims designed for cutting 1/8, 3/16, 1/4 or 3/8 in. keyways in bore sizes from 1/2 to 1 1/2 in. Push-type broaches can be used with any hand-operated arbor press or any hydraulic press with adequate throat depth. Other broach sets are available for cutting keyway sizes from 1/16 to 3/4 in. and bores from 1/4 to 3...
Read More »