Momentive    Albany, NY 12211
May 14, 2012 By surrounding fragile solar cells of crystalline PV module with flexible, stress dissipating silicone matrix, SilTRUST Encapsulant helps maximize performance in harsh outdoor environments while optimizing light-to-electricity conversion yield. Refractive index of transparent encapsulant closely matches that of glass, minimizing energy-dissipating reflection of sunlight away from solar cell. At 80°C, silicone module is virtually stress-free.

Aremco Products, Inc.    Valley Cottage, NY 10989
Apr 24, 2012 Applicable to diverse industries, Corr-Paint(TM) CP4020 single-part, gray-pigmented, silicone-based, water-dispersible coating system adheres to sandblasted as well as marginally prepared surfaces. Coating dries at room temperature and cures as coated structure is ramped up to its operating temperature. At temperatures to 1,100°F, resultant coating is color stable and resistant to oxidation, UV light, humidity, and salt spray conditions.

Engineered Materials Systems Inc.    Delaware, OH 43015
Apr 11, 2012 Intended for printer head and circuit assembly applications, 357-348 Wire Bond Encapsulant and Flexible Circuit Bonding Adhesive imparts protection while reducing stresses associated with thermal cycling. Product exhibits chemical resistance to inks and adheres to flexible circuits, FR4, and metal substrates. Properties meet circuit assembly and semiconductor standards for ionic cleanliness (extractable ions) to prevent corrosion in high-temperature and -humidity environments.

Aremco Products, Inc.    Valley Cottage, NY 10989
Mar 28, 2012 Used to insulate moisture-sensitive electrical components, including cartridge heaters and high power case resistors, Sil-Bond(TM) 905 demonstrates moisture resistance with weight gain of less than 1% after exposure to 900°F and 24 hours water immersion. Shrinkage rate is also less than 1% and dielectric strength is greater than 250 V/mil. Supplied as powder and liquid system, compound cures in 12-16 hr at room temperature and 30 min each at 150, 250, 350, and 450°F, respectively.

Aremco Products, Inc.    Valley Cottage, NY 10989
Feb 07, 2012 Consisting of unfilled, 100% solids epoxy system, Aremco-Bond(TM) 526N can be used continuously at temperatures to 570°F. Product features volume resistivity of 4.0 x 10¹⁴ W-cm, dielectric strength of 450 V/mil, and dielectric constant of 3.01 at 1.0 Hz. Flexural and tensile strengths are 16,000 and 2,800 psi, respectively. With 1:1 mix ratio, epoxy provides mixed viscosity of 4,000 cP and pot life of 2.5 hr. Product adheres to ceramics, glass, metals, and plastics substrates.

Freudenberg & Co. Limited partnership    Weinheim   Germany
Jan 18, 2012 To meet sealing challenges surrounding food and beverage processing, Fluoroprene® XP 40 withstands both chemically aggressive cleaning agents and sterilizing steam as well as high-fat concentrations and flavoring agents found in processing applications. This universal sealing material is resistant to temperatures from -15 to +200°C and suited for facilities that manufacture and process different products with range of formulas and processing conditions.

Master Bond, Inc.    Hackensack, NJ 07601
Jan 13, 2012 Suited for medical applications, silver-filled EP3HTSMED is 100% reactive with tensile shear strength exceeding 1,000 psi and volume resistivity less than 0.001 Wcm. Thixotropic paste requires no mixing and needs only contact pressure during heat cure of 20-40 min at 300°F or 40-90 min at 250°F. Serviceable over temperature range of -60 to 400°F, electrically conductive product is resistant to severe thermal cycling as well as water, fuels, oil, and most organic solvents.

Master Bond, Inc.    Hackensack, NJ 07601
Nov 22, 2011 Formulated for bonding, sealing, and coating, UV16 single-component, no-mix system cures in 1 min or less at room temperature with commercial UV light sources. This 100% reactive epoxy, uninhibited by oxygen, does not release any solvents or volatiles during cure. Cured in thicknesses up to 0.125 in. with 2%-3% shrinkage rate, solution delivers tensile strength exceeding 4,100 psi and Shore D hardness greater than 75. Product has viscosity of 200-400 cps and adheres to array of substrates.

Bayer MaterialScience, LLC - Coatings, Adhesives & Sealants    Pittsburgh, PA 15205
Oct 14, 2011 Used for restoring water slides, polyaspartic gelcoat technology has life expectancy of years and dry times that accelerate return-to-service - sometimes as soon as 24 hr. Low-odor product is formulated for optimal durability, weather-ability, color and gloss retention, and ultra-low VOC content. This spray-applied, 2-component, ambient-cure gelcoat also has temperature application range that extends season for restoring outdoor slides.

Color Wheel Paints & Coatings    Orlando, FL 32808
Oct 04, 2011 To create base coat that promotes efficient use of finish coat, 1260 Flex Lox Surface Sealer is formulated for optimal adhesion, chalk-binding, and sealing as well as hiding capability. Primer is designed for previously painted surfaces and uses acrylic resins to penetrate and seal substrate. With properties that promote topcoat adhesion, low-odor solution meets LEED standard for low VOC (less than 50 g/L) and is designed as companion primer for use with Flex Lox Flat and Satin.

Aremco Products, Inc.    Valley Cottage, NY 10989
Jun 22, 2011 Combining Teflon®-coated fiberglass tape with silicone adhesive, Pyro-Tape 682-CR is suited for insulating pipes and ductwork, and as non-stick covering for chutes, slides, heat-seal bars, and molds. Tape is rated from -100 to 500°F with adhesive strength of 50 oz/in. and tensile strength of 120 psi. Pyro-Tape 682-CR is available in standard sizes of ½ and 1 in. wide x 36 yards with cross-sectional thickness of 0.009 in.

Pecora Corp.    Harleysville, PA 19438
May 23, 2011 Extruded into preformed strips or custom shapes that bridge over existing joint, Sil-Span(TM) silicone compound waterproofs building envelope while preventing damage to building substrate and maintaining original aesthetics. Product can be custom colored and textured to match virtually any finish. Validated by Sealant Waterproofing and Restoration Institute, Sil-Span profiles meet ASTM C 1523, offer 200% movement capability, and are resistant to UV rays and weathering.

Aremco Products, Inc.    Valley Cottage, NY 10989
May 03, 2011 Intended for potting and encapsulating in electrical and electronic applications, Aremco-Bond(TM) 2315 provides flexural strength of 12,300 psi, volume resistivity of 1.0 x 10¹⁵, and dielectric strength of 480 V/mil. Black-pigmented, thermally conductive product offers resistance to acids, alkalis, organic fluids, and salts. Featuring mixed ratio of 100 parts resin to 25 parts hardener by weight, Aremco-Bond 2315 cures in 2 hours at 160°F plus 2 hours at 300°F.

Power Adhesives Ltd    Charlotte, NC 28209
Apr 19, 2011 With KNOT-TEC(TM) Wood Repair Starter Kit, manufacturers have tools needed to begin repairing knots and filling in wooden surfaces. Components are non-flammable, use no harsh solvents, and can be safely used on windows, doors, furniture, wood floors, and cabinets. Supplied in black molded toolbox, kit includes hot melt adhesive glue gun, Mouseplane® for flush trimming of glue lines and wood, silicon drip mat, gun stand, 2 heat sink blocks, 12 TECBOND(TM) 10-in. glue sticks, and instructions.

Henkel Corporation    Rocky Hill, CT 06067
Apr 11, 2011 Based on modified silane polymers, Terostat® MS 500(TM) is designed for use in fully automated framing of crystalline solar modules. It achieves instant handling strength and provides primerless adhesion to glass, metal, and plastics as well as long-term resistance to challenging weather conditions. Flexible over temperatures from -20 to +100°C, UV- and damp heat-resistant adhesive can compensate for differing rates of thermal expansion between substrates.

Laird Technologies    Chesterfield, MO 63017
Mar 29, 2011 With thermal conductivity of 3.5 W/mK, Tputty(TM) 506 series is specifically formulated to fill large and uneven gaps in high-wattage electronic assemblies. Soft, single-part, silicone putty does note require any cure, transfers little to no pressure between interfaces, and is non-abrasive. Conformable and reworkable, filler is colored for automatic detection systems and has viscosity that eliminates bleed and pump-out associated with grease.

Master Bond, Inc.    Hackensack, NJ 07601
Mar 03, 2011 Used for coating, lining, bonding, or sealing, EP21AR withstand acidic environments - including immersion in 96-98% sulfuric acid and 36% hydrochloric acid for over one year. This 2-component epoxy, with dielectric strength of 400 V/mil, also acts as electrical insulator and is serviceable from -60 to +275°F. It produces abrasion-resistant bonds with tensile strength over 10,000 psi, shear strength exceeding 2,700 psi, and compressive strength greater than 14,000 psi at 75°F.

DuPont Co., Packaging & Industrial Polymers    Wilmington, DE 19898
Feb 23, 2011 Because ionomer-based DuPont(TM) PV5400 Series is fundamentally resistant to moisture intrusion, it is possible to achieve lasting edge integrity without caulking or additional edge sealing. Compared with traditional EVA and PVB encapsulants, PV5400 Series has up to 100 times more electrical resistivity, offering modules optimized electrical insulation, which minimizes current leakage. Products are available in roll form with sheet thicknesses of 400 and 500 microns.

Saint Gobain Performance Plastics    Garden Grove, CA 92841
Feb 08, 2011 Reducing noise transfer between rooms, Green Glue Noiseproofing Sealant adheres firmly to wood or metal studs, concrete, plasterboard, and other types of building substrates and will not dry out or crack with age. Water-based and non-toxic product has minimal odor and can seal cracks in floors, walls, and ceilings. Applied along edges and joints, it can be painted once dry and cleans up with soap and water.

All Packaging Machinery Corp.    Ronkonkoma, NY 11779
Feb 02, 2011 Incorporating speed control and digital temperature controls, USDA-approved HCBS rotary band sealer offers odorless and smokeless sealing with ¼ in. secure final seal and trim. Dual heating sections and dual cooling sections ensure secure seal, while trim after seal system and vacuum trim accumulation system ensure clean, straight trim directly at seal edge. Heavy-duty, chrome-plated sealing assemblies handle PE, PP, Polyolefin, and PVC shrink films.