Aremco Products, Inc.
Valley Cottage, NY 10989
Oct 09, 2009 Single part, water-dispersed, ceramic-silicone sealant Fiber-Bond(TM) FO-380 seals fiber optic strands into stainless steel and ceramic ferrules used to support fiber optic bundles for high temperature applications to 716°F. It has viscosity of 60 Cp, solids content of 21.0% by weight, and offers moisture resistance and dielectric properties across operating temperature range. Applied by brush, dipping, or spraying, sealant sets at room temperature and cures fully in 45 min at 450°F.

Amerimax Building Products, Inc.
Plano, TX 75024
Jun 30, 2009 Available in 6 colors, Aluma-Shield(TM) low-maintenance aluminum patio cover system features Teflon® additive and will repel oil, dirt, dust, and stains. It provides real wood appearance with combination of matte finish and semi-gloss cleaning characteristics. Offering protection against UV, salt, pollution, and weathering, customizable paint system makes surface resistant to chalking, fading, cracks, peels, warps, and termites.

Master Bond, Inc.
Hackensack, NJ 07601
Apr 15, 2009 Storage-stable, one component, low viscosity system, EP19HT adhesive/sealant, impregnant, and liner features viscosity of 500-600 cps at 75°F and cures readily at elevated temperatures to tough, chemically resistant thermoset plastic. Recommended cure is 1 h at 250°F, while shorter cures can be achieved at temperatures between 325-350°F. Exhibiting minimal shrinkage upon cure, product has service operating temperature range of -60 to 400°F and tensile strength greater than 10,000 psi.

Deposition Sciences, Inc.
Santa Rosa, CA 95403
Jan 26, 2009 Applied onto thin stainless steel sheets via MicroDyn® sputtering technology, High Temperature Spectral Metal Coatings withstand temperatures up to 400°C. Coated sheets can be cut and formed to specific sizes and shapes, depending on customer requirements. Mounting features, such as slots, screw holes, and tabs can be formed into mirror after coating is applied, and sized mirrors can be formed into precise curves and cylinders with radii as small as 25 mm.

Integran Technologies Inc.
Pittsburgh, PA 15241
Nov 17, 2008 Designed to provide low frequency magnetic shielding to polymer, composite, and metal parts, Nanovate(TM) EM coating can be applied selectively, allowing shielding performance to be focused where it is needed on part. Coating can be used to stiffen and strengthen shielded polymer, composite, and metal substrates. Product suits sensors, transducers, and other applications sensitive to low frequency magnetic interference.

Master Bond, Inc.
Hackensack, NJ 07601
Sep 26, 2008 Available in ½ pint, pint, quart, gallon, and 5 gal kits, Master Bond EP30 features low viscosity, chemical resistance, dimensional stability, hardness, optical clarity, and electrical insulation properties. It is used in potting and encapsulating electronic components as well as in bonding optical elements, and has adhesion to metals, ceramics, glass, and plastics. EP30 has lap shear strength exceeding 3,000 psi for aluminum to aluminum bonds, and low shrinkage upon cure.

Kimball-Midwest
Columbus, OH 43228
Jul 28, 2008 Protecting materials by reducing heat transfer during soldering, brazing, welding, and open flame contact, Therma-Shield Heat Protection Paste eliminates disassembly of valves and other components. It can be applied to almost any surface or material, and conforms to irregular shapes and surfaces to provide total coverage and protection. Product is non-flammable, non-toxic, non-corrosive, and biodegradable, and helps eliminate waste as it can be applied only where needed.

Deposition Sciences, Inc.
Santa Rosa, CA 95403
May 29, 2008 Designed to maximize curing wavelengths between 220-400 nm and minimize rest of visible and IR spectrum from 450-2200 nm, UV Spectral Metal features MicroDyn® sputtering technology and is used as reflector behind curing lamp. Stable over temperature/humidity changes, it is coated onto highly polished, standard size aluminum sheets. With ability to customize/fabricate products after coating, long trough reflectors for inline exposure systems can be created using multiple lengths of product.

Cortec Corp.
St. Paul, MN 55110
May 29, 2008 Designed to replace phosphatizing and chromating systems, VpCI(TM)-440 protects multi-metal substrates from corrosion while preparing metals for surface bonding and coating. Non-toxic, non-hazardous, water-based coating can be applied with conventional equipment such as sprayers, dipping tanks, steam cleaners, and power washers. Self-preserving product is environmentally safe and does not require use of biocides.

Aremco Products, Inc.
Valley Cottage, NY 10989
Jan 17, 2008 Pyro-Paint(TM) 634-BNSC is single part, odorless, water-dispersible coating formulated to resist molten metals, glasses, plastics, and salts as well as non-ferrous metals such as molten aluminum and magnesium. It provides highly lubricious and chemically resistant interface between molten material and underlying refractory structure. Applied with brush, roller, or spray equipment, coating dries at room temperature in 1-2 hr and cures fully in 1-2 hr at 200°F.

Chemetall Oakite Products, Inc.
Berkeley Heights, NJ 07922 2712
Jan 10, 2008 Providing iron phosphate coating for ferrous metals, Chem Cote 3010 works at temperatures below 90°F, eliminating use of any burner. It is pre-paint treatment for iron and steel that makes resulting surface highly resistant to corrosion.

Weld-Aid Products
Detroit, MI 48212
Dec 03, 2007 Made of 95% zinc, 1st Zinc is used on metal parts and assemblies as either protective primer coat to be later topcoated or as standalone coating. Formula provides corrosion protection in cold-galvanizing applications and meets requirements listed in ASTM-780, ASTM-D-520, Fed Spec DOD-P-21035A, MIL-P-26915A, and SSPC-Paint 20 specifications. Product is available in aerosol cans and bulk gallons.

Aremco Products, Inc.
Valley Cottage, NY 10989
Mar 26, 2007 Consisting of inorganic, ceramic and metal-filled paste, Pyro-Putty® 653 bonds tenaciously to cast iron, steel, and stainless steel. Thixotropic formula can be applied to horizontal and vertical surfaces in cross sections up to ½ in. thick. It is chemically inert and will not decompose at ultra high temperatures. Resistant to most fuels, solvents, and other corrosives, compound is suited for sealing cast steel castings, housings, pipes, and flanges.

Birchwood Casey
Eden Prairie, MN 55344 2138
Mar 13, 2007 Meeting multiple Federal Government Green Purchasing requirements, INTERCEPT® SPS shrink film, stretch film, flat stock, and bags protect products from corrosion and deterioration during shipment and long-term storage. HDPE film, infused with metallic copper particles and activated carbon, proactively neutralizes and removes corrosive elements in air around product while also killing any acid-producing bacteria, mold, or fungus. It has no chemical content and produces no fumes.

Deposition Sciences, Inc.
Santa Rosa, CA 95403
Feb 19, 2007 Suited for applications in general lighting, medical systems, digital imaging, LED lighting systems, and portable optical systems, HeatBuster® Spectral Metal Thin Film Coating meets severe abrasion, adhesion, humidity, and salt fog tests of Mil-C-675 standards. Stable over temperature and humidity changes, dichroic hybrid coating operates over range of angles, and is designed to be highly reflective over selected bands of wavelengths and minimally reflective over rest of the spectrum.

Master Bond, Inc.
Hackensack, NJ 07601
Jan 31, 2007 Suited for sealing and joining of metals, plastics, electrical insulations, protective coatings, and formed-in-place gaskets, Master Sil 700 silicone elastomer compound has dielectric strength of 530 V/mil and 400% elongation. Silicone adhesive/sealant features paste consistency and does not sag, slump, or run off surfaces. It cures at ambient temperatures to a flexible rubbery solid when exposed to atmospheric moisture and remains flexible over temperature range of -75 to 400°F.

Master Bond, Inc.
Hackensack, NJ 07601
Jun 12, 2006 One component, heat curing epoxy adhesive/sealant EP17 cures at temperatures from 300-350°F for 60-90 minutes. Flowable paste has 8,700 psi tensile strength, 387,000 psi tensile modulus, Shore D hardness greater than 90, and compressive strength greater than 13,000 psi. MIL-MMM-A-132 compliant, 100% reactive compound is resistant to chemicals, including fuels and acids, and bonds to metals, glass, ceramics, vulcanized rubbers, and plastics.

Cotronics Corp.
Brooklyn, NY 11232
Mar 17, 2006 Packaged in dispensing cartridges, 450°F Instant Metal 7056AL forms solid metallic aluminum layer that adheres to smooth, rough, or porous surfaces as well as most plastics, metals, ceramics, glass, and wood. It cures in 4-8 min at room temperature without objectionable sulfur odors. Once cured, metallic composite is machinable with standard tools and can also be tapped, drilled, and threaded.

Aremco Products, Inc.
Valley Cottage, NY 10989
Jul 14, 2005 Pyro-Putty® 1000 sealant and metal repair compound is 2-part, powder and liquid system that operates to 1,400°F. Dispensed into place in cross-sections up to ½ in. thick, water-based, ceramic- and aluminum-filled paste sets at room temperature in 16–24 hr. It can be cured in-situ or by heating for 1–2 hr @ 160°F. Containing no asbestos or VOCs, environmentally compliant compound is resistant to thermal shock, corrosive chemicals, and solvents.

Cortec Corp.
St. Paul, MN 55110
Jun 15, 2005 VpCIâ„¢ 374 Waterborne Metal Primer is formulated as fast drying, thixotropic coating with low viscosity that resists sagging. Built-in VpCIâ„¢ Anti-Corrosion System provides protection against corrosion, sunlight, and weather for carbon steel, cast iron, stainless steel, and aluminum. Designed for production base coating using conventional spray or airless spray, product can also be applied by brush or roller for touch-up and field use.