New Welders Products

Welder/Generator/Compressor offers truck-mount solution.

Featuring 20 x 36 x 48 in. design, PowerBox(TM) 280MP utilizes 18 hp gasoline Kohler engine to power its 20 cfm Quincy compressor and 200 A/5,500 W generator/welder combination. Self-contained, hydraulically driven PowerBox 280HD, with similar characteristics as 280MP, suits vehicle applications that already utilize power take off system. Both models mount onto side pack of service body, into...

Ultrasonic Welding System features vertical stroke.

With total stroke of 1.9 in., 20 kHz Ultraweld Linear 20 employs actuator that works in linear up/down motion and may be tooled for nonferrous welding applications. Vertical stroke makes tooling parallel front to back at all times. Along with precision roller bearing slide, system features dovetail mounting, flow controls, and adjustable upper and lower positive stops. Polar mounted ultrasonic...

Microscope-Based Welding Systems minimize rework time.

Microwelding Systems enable user to see exactly where weld puddle is applied for repairing molds and dies and lets operator produce welds with less than 0.0005 in. of sink in heat affected zone. Featuring microscope and lighting for magnification needed to maintain arc necessary in low-amperage miniature TIG welding, systems include power supply, hot plates, micro-blasters, and all tools for pre-...

Generator/Welder uses 3/32 and 1/8 in. diameter electrodes.

Power Arc(TM) 5500 provides 5,500 W of surge ac generator power and 125 A of ac welding amperage. Welding capacity is delivered by Robin/SubaruÃ-® overhead cam engine, or HondaÃ-® overhead valve engine, both rated at 9 hp. Single-range output control lets user dial in correct weld settings, while built-in circuit breakers protect tools and unit from power overload. Enclosed in tube-frame...

Metal Stamping for Construction Tool Applications

Metal stamping is a highly versatile manufacturing technique, capable of producing quality components at tight tolerances.

Welders are used for spot and projection welding.

Featuring force range of 675-1,055 lb, 24 in. throat rocker arm welders are offered with 25, 30, and 50 KVA ac transformers. With force range of 1,000-4,045 lb, RWMA Size 0-3 press welders have ac transformers rated from 50-250 KVA. Press welders rated 80, 100, and 150 KVA, as well as 50 KVA rocker arm welder, are stocked with 440 V primary power. Product line can also be customized to...

Welding System is available in various configurations.

Ready-Pak(TM) kits are available in 4 configurations with various power sources to meet application needs. All kits include LF-72 wire feeder featuring 2-roll MaxTrac(TM) drive system for accurate wire feeding. Other components are power source, drive rolls and wire guide, wire feeder control cable, welding gun, work lead and clamp, and HarrisÃ-® Flowmeter/Regulator and gas hose. Two kits...

Welder offers spool-gun ready capabilities.

Model Power MIGÃ-® 255C provides continuous control over range of 30-300 A with rated output of 250 A at 40% duty cycle. Built-in electronics drive PrinceÃ-® XL or MagnumÃ-® SG spool gun for aluminum welding capabilities, and 115 V auxiliary receptacle can power grinder or other equipment. Cast aluminum industrial wire drive system features dual driven rolls, numeric tension...

Robotic Cell welds small- to medium-sized parts.

Dual, fixed-table eCell(TM) system is capable of MIG, Synergic MIG, MIG Pulse, and flux-cored arc welding procedures on parts that can be welded without reorientation. It welds variety of materials including steel, stainless steel, and aluminum. Digitally-controlled, 350 A inverter welding power source is capable of high-speed communication and is delivered with 60+ factory-programmed waveforms...

TIG Welding Torch suits field applications.

Air-cooled Model CS 300/300V eliminates need for complex water-cooled components. It handles amperages up to 300 A without overheating and features high flex cable assembly to minimize operator fatigue.

Welder/Generator offers 5,500 W AC generator power.

Featuring Robin/Subaru-® 9 hp EX 27 engine, Weldanpower-® 125 provides DC stick welding power with 125 DC Amps for variety of projects and 5,500 surge watts of AC generator power for work lights, tools, and pumps. Unit is capable of welding steel, stainless steel, cast iron, or hardfacing projects. Tubular roll cage provides added protection and many lift handle points. Two people can transport...

Optimize Your Storage or Distribution Facility with Steel King Rack Solutions

Steel King racks are designed to meet seismic requirements in the most demanding conditions. Our durable storage products help your company save on maintenance costs. Check out our product video or download our Rack Planning eBook to learn more.