Level Transmitter offers 4-20 mA or 0-5 Vdc outputs.
Level Transmitters

Level Transmitter offers 4-20 mA or 0-5 Vdc outputs.

Model CS001 RF Capacitance Level Transmitter provides linear level measurement in extreme process temperatures and fluid conditions. It features fully programmable 4-button calibration for specific medias and is available in NEMA 4 (IP65), or explosion-proof housing. Probe is 316L stainless steel, comes in lengths up to 120 in., and contains Teflon encapsulated electrode. Applications include...

Read More »
Transmitters communicate in HART and Fuji protocols.
Transmitters

Transmitters communicate in HART and Fuji protocols.

Intrinsically safe, explosion-proof Series FCX electronic transmitters measure, display, alarm, and output level, pressure, and/or flow data. Type All includes gage, absolute, differential pressure, flanged level, and remote seal models. Type Alle includes gage and differential pressure models. Accuracy is ±0.07% of span for Type All, and ±0.1% of span for Type Alle. Turndown is 100:1...

Read More »
Ultrasonic Transmitter measures levels up to 40 ft deep.
Level Transmitters

Ultrasonic Transmitter measures levels up to 40 ft deep.

Two-wire LU 12-14 MiniMe provides non-contact level measurement up to 10 ft in 1 in. mount, or up to 25 or 40 ft in optional 2 in. mount. Accuracy is ±0.15% of span while resolution is 0.125 in. Signal output is 4-20 mA. PC/ABS enclosure is rated NEMA 6X with Kynar® transducer. Transmitter features digital infinity surface mapping, fail-safe intelligence with diagnostic feedback, and...

Read More »
Transmitters

Transmitters suit demanding applications.

Series TX1500 features 2-wire operation power, which is obtained directly from 4 to 20 mA loop, with no need for separate power input. Isolation to 1500 V rms eliminates possibility of electrical ground loops between signal source and receiver. Overvoltage of 120 Vac may be applied across input or output leads for 1 min in all models with voltage or thermocouple input. Reverse polarity of 400 Vp...

Read More »
I/P Transmitter uses natural gas as pneumatic supply.
Flow Transmitters

I/P Transmitter uses natural gas as pneumatic supply.

Model IPX2 current-to-pressure transmitter is CSA approved to be used with sweet natural gas consisting of up to 20 ppm of H2S. Approvals allow installation in explosion-proof hazardous areas. Loop-powered unit accepts current signal from DCS-, PLC-, or PC-based control system and converts it to 22 available pneumatic signals proportional to input. It is rated to operate in ambient conditions...

Read More »
Transmitter/Receiver offers range up to 10 miles.
Signal Receivers

Transmitter/Receiver offers range up to 10 miles.

Long Range Radio Control Transmitter and Receiver are for use in wireless remote control applications. Crystal controlled transmitter accepts dry contact input and transmits encoded message to receiver. Encoding is done via FSK (frequency shift keying). Upon detection and verification of encoded control signal, receiver triggers remote device via dry contact. Single, four, and sixteen channel...

Read More »
Pressure Transmitters are TUV-certified for safety.
Pressure Transmitters

Pressure Transmitters are TUV-certified for safety.

Series B45 absolute, differential, and gauge pressure instruments are certified for high availability and safety service. They have hardware and software redundancy, comprehensive self-checking system, and primary and secondary current sources to ensure safe fault indication if failure occurs. These features allow single B45 unit to be installed where two conventional transmitters are usually...

Read More »
Pressure Transmitter provides ±0.1% full scale accuracy.
Pressure Transmitters

Pressure Transmitter provides ±0.1% full scale accuracy.

Series 642 measures pressure of liquid and compatible gases up to 100 psig. It resists effects of shock and vibration and is constructed of corrosion-resistant 316 or 316L stainless steel wetted parts. Unit features 2-wire operation and reverse polarity protection. Zero and span are independently adjustable. Four models are offered with pressure ranges from 0-15 psig, 0-30 psig, 0-50 psig, and...

Read More »
Flow Transmitter integrates probe and transmitter.
Flow Transmitters

Flow Transmitter integrates probe and transmitter.

The PT Transmitter is a fully integrated pitot based flow meter that reports and displays velocity, volumetric flow or mass flow, gas temperature, and duct pressure of process. Unit is mounted using compression fitting and only requires one cable for power and signal. Fully configurable platform allows operator to allocate 2 analog outputs and relay alarms to any of measured and calculated...

Read More »
Transmitter continuously monitors liquid levels.
Level Transmitters

Transmitter continuously monitors liquid levels.

Single-float, 2-wire LV50 series utilizes proportional 4-20 mA signal output. Constructed of 316 stainless steel, transmitter is able to operate at process temperatures up to 300°F. Explosion-proof model (LV51) is rated for use in Class I, Div. 1, Groups B, C, and D, and Class II, Groups E, F, and G environments. Completely submerged and unaffected by fumes or vapors, unit range is from 5...

Read More »

All Topics