New Switches Products

Lead-Free Tactile Switches meet RoHS directive.

Series HP features 6 mm through-hole and surface-mount switches with insert-molded terminals to lock out flux, solvents, and other contaminants. Circuit is normally-open, SPST OFF, momentary ON. Measuring .244 in. square, body is molded in heat-resistant resin, which meets lead-free solder processing requirements and has UL flammability rating of 94V-0. Switches are available with silver contacts...

Single Rod Limit Switch is used in bulk solids.

Soliphant T FTM 20/21 detects level limit in fine- or coarse-grained, non-fluidized bulk solids with grain size up to 1 in. Tilted piezo drive, located inside tip of sensor rod, does not contact medium. Mechanically balanced design maximizes resistance to vibration and build-up, resulting in minimal false trips. Permissible process temperature ranges up to 300Ã-

Data Switch automatically accommodates for signal loss.

Model 4148 Self-Configuring Normal/Redundant Fallback Switch allows data signals entering switch from 2 origination devices to be channeled to 2 destination devices. Along with Normal and Redundant Fallback modes, product features Crossover position and can also be controlled manually via front-panel push button. It is equipped with 4 front panel LEDs that indicate connectivity status and verify...

Tuning Fork Switch offers high and low level indication.

Series TF-100 provides no-calibration solution to point level measurement of clean liquids and is available with relay, current, or PNP outputs. Made of 316 stainless steel, sensor is offered in standard and sanitary versions. When material level reaches predetermined point on sensing element, it causes change in status in electronic unit, resulting in output that can operate alarms,...

How to Effectively and Efficiently Clean Heat Exchangers, Part I

An introduction to a three part series about the importance, benefits, and methods of cleaning heat exchangers.

Safety Interlock Switches meet safety Category 4 standards.

PICO-GUARD(TM) Series SFI-M12SS consists of IP67-rated, fiber optic, M12 barrel-style interlock switches intended for use with PICO-GUARD controllers in personnel safety and equipment-protection applications. Fibers are polyethylene jacketed with fluoropolymer sheathing for applications that must withstand harsh chemicals and gases. Stainless steel switches provide non-contact means of...

Safety Switch features solenoid and LED signaling.

Available in 2 signaling versions, Series FG Type A requires no external wiring and has LEDs switched on via solenoid power supply, while Type B allows connection to contact block, making it possible to control different states of switch. Metal-bodied switch features 3 conduit entries, actuator holding force of 2,500 N, integrated contact blocks with 4 poles, rotating head, and protection rating...

Switches enable use of first, second, or both batteries.

Rated from 6-36 V, M-750 Series Battery Selector and Master Disconnect Switches operate as emergency shut down when vehicles or equipment are unattended. Vaporproof, weatherproof units, corrosion-resistant and ignition-protected to USCG 183.410, are offered in designs with or without key, pilot light, or alternator fields disconnect. As dual battery system, switches enable 2 batteries to power...

Switches are available with polyurethane cables.

Series FA and FB pre-wired position switches are offered with optional polyurethane cable, which lends to cable strength and durability. Used as alternative to standard PVC cable, polyurethane option makes product suited for use in applications such as machine tool industry, where resistance to higher temperatures, sheath abrasion, and oils and solvents are required.

Safety Switch uses non-detachable, rotating actuator head.

Safety Interlock Switch allows direction of actuating head to be changed without detaching it from switch body, minimizing chances of damage during installation. Switch uses only 2 fastening screws, facilitating actuator orientation. Versions with actuating force of 30 N or stainless steel parts are also available.

RF Level Switches are immune to build-up.

ShieldPoint(TM) RF Capacitance Switches provide point level detection in applications ranging from sticky slurries to low dielectric bulk solids. Single-point ShieldPoint 300 features 3-element shielded probes and 10 A DPDT relay, while multi-point ShieldPoint 400 offers variety of probe options, TeflonÃ-® coated or bare rods and cables, along with 2 SPDT 10 A relays. Both are housed in...

Don't Let Your Money Drain Down the Hole...Drill Steel with Euroboor

As a globally recognized manufacturer of industrial grade portable tools, Euroboor is at the forefront of drilling and cutting technology. Our reputation as an industry leader is built on robust products that fit a wide range of industrial cutting and drilling applications. See our video to learn more about all of our quality products.