New Power Supplies Products

PC Card Power Supplies produce 150 W of power.

Series PSSBU150 universal input, open ac/dc power supplies provide single output voltage from 3-50 Vout. Housed in 3 x 5 in. package measuring 1.32 in. high, units operate up to +70Ã-

Harmonic Attenuator Module works with DC-DC converters.

High-boost Model VI-HAM is a universal ac input, PFC front-end module optimized for use with Series 375 DC-DC converters up to 600 W. Consisting of full-wave rectifier and high-frequency, zero-current switching boost converter, unit includes active inrush current limiting, over temperature and short circuit protection, control, and housekeeping circuitry.

Modifiable DC/DC Converters come in half-brick package.

Suited for applications requiring nominal 12 or 24 Vin, LV series converters operate over -40 to +100Ã-ºC temperature range and feature 6-sided shielding, remote sense, trim to 10%, case ground pin, and remote on/off. Each unit produces up to 150 W and 20 A of output current at 3.3 and 5 Vout with efficiencies of up to 88%. Converters feature dc input of 10-30 Vin and can be configured to...

POL Converters support intermediate bus converters.

Available in packages with surface mount, open frame, PTH design, NFA Series DC-DC converters come in 10, 16, and 20 A models. Non-isolated Point-Of-Load converters, featuring efficiencies up to 95%, come in positive and negative enable logic models with monotonic start-up with pre-bias. With input voltage range of 6-14 V, products support 4:1, 5:1, and 6:1 intermediate bus converters. Series...

Everything You Need to Know About E-Textiles

This ebook provides an in-depth overview into everything you need to know about E-Textiles.

Power Injectors suit Power-over-Ethernet applications.

Available in 8, 16, and 24 port versions, multiport Enterprise Midspans offer full 15.4 W per port and can upgrade existing architecture with total output power of 370 W. Power-over-Ethernet allows both power and data to be carried over single Ethernet cable. USB port enables diagnostic testing via laptop so no adapter cables are required. Each Midspan comes with software to control and monitor...

Welding Power Source features lightweight, portable design.

Weighing 40 lb, CST(TM) 280 Stick/TIG Welding Power Source provides output of 280 A/31 V at 35% duty cycle or 250 A/30 V at 60% duty cycle. Users can select between high and low voltage inputs to accommodate domestic and international requirements. If the arc start requires additional output amperage, Adaptive Hot Start(TM) automatically provides it, preventing electrode from sticking and...

DC/DC Converter includes integrated boost and catch diodes.

Model LT3470 40 V micropower step-down dc/dc converter operates from input voltages of 4-40 V, delivering up to 200 mA of output current, optimizing it for 2-cell Li-Ion, wall adapter or automotive power sources. Burst ModeÃ-® operation reduces quiescent current to 26 Ã-µA. Hysteretic control scheme provides output ripple of less than 10 mVp-p. Available in low profile ThinSot package,...

Integrated DC/DC Converter offers 570 W/in.-³ density.

Used to adjust and stabilize input power, FunctionPAKÃ-® FX5545G108 DC-to-DC buck converter can also stabilize, filter, reduce ripple, and shift DC voltage levels or stabilize battery voltage outputs. It comes in 20-port, SMT BGA package that measures 0.58 x 0.48 x 0.126 in. and is rated for 4 A max current and 15 W output power with 1 Ã-µA shutdown current. Device converts 2.5-6 V inputs...

DC/DC Converter produces 5 A output.

Suited for PCB layouts with limited space, 5SR75.5SN non-isolated DC/DC converter offers remote ON/OFF, output voltage trim, and Input Under-Voltage Lockout features as well as continuous short circuit protection. User-selectable output voltage range is 0.75-3.63 Vdc, and input voltage range is 3.0-5.5 Vdc. Packing up to 15 W in 0.8 x 0.45 x 0.245 in. SMT package, converter has switching...

Welding Power Supply has spool gun ready capabilities.

Power MIGÃ-® 255C features Diamond Core Technology(TM) for minimal spatter. Spool gun ready capabilities include built-in electronics to drive PrinceÃ-® XL or MagnumÃ-® SG spool gun for aluminum welding and second gas solenoid to facilitate spool gun connection. Offering continuous control over amperage range of 30-300 A, rated output is 250 A @ 40% duty cycle. Unit has 115 V...

How SpinSelect Can Save You Time and Money

Thanks to the unique SpinSelect™ Multi-Pocket selectable quick change tool holder, it's time to rethink the range, complexity and volume of parts that your lathe can produce. Our Spin-Select™ tool was created to increase productivity and consistency by decreasing downtime associated with lathe cutting tool and insert setups or changeovers. This product is a game-changer for the industry and we're pleased to show you why.