New Multiplexers Products

Analog Multiplexers are offered in two versions.

Suited for -

Antenna Multiplexers integrate 4 or 8 antenna ports.

Designed to minimize number of readers deployed when multiple read-points are required, MXH and MXU antenna multiplexers operate at HF Frequency of 13.56 MHz and UHF Frequency of 860-960 MHz, respectively. Each multiplexer is controlled by either host processor or reader module, allowing any of 4 or 8 antennas to be addressed explicitly using 3 GPIO pins.

Analog Front End enables inductive touch sensing.

Designed to work with 8-, 16-, or 32-bit PIC-® microcontroller or dsPIC-® Digital Signal Controller, Model MCP2036 includes multiplexer, frequency mixer, amplifier, driver, and voltage reference. Inductive touch sensing works through plastic, stainless steel, or aluminum front panel, as well as through thick gloves and on surfaces where liquid is present. Housed in 16-pin 4 x 4 mm QFN package...

Multiplexers target high-density CCTV applications.

Available for use over multimode or single mode optical fiber, F32V8DT/R(M)(S)1 Series video/data multiplexer transmitters/receivers support 32 channels of video with 8 channels of bi-directional serial data. Units offer 10-bit RS250C Short-Haul Quality video performance and can transport video up to 20 km between locations. Series is suited for applications such as airports and parking garages,...

Screen Printing vs. Digital Printing: Five Key Decision Factors

Learn about the key factors for deciding between screen printing and digital printing.

Antenna Multiplexer can be equipped with 4/8 antenna ports.

Designed to ease integration for devices requiring multiple read-points, GAO733001, MXH and MXU antenna multiplexers feature either host or reader module for any of 8 antennas to be explicitly addressed using 3 GPIO pins. Multiplexers can be added for increase in number of antennas to allow module to support beyond 8 presenting scalable solution.

I²C Switches/Multiplexers provide bus lockup detection.

Capable of detecting, isolating, and notifying slave bus lockup conditions, 8-channel MAX7356/MAX7357/MAX7358 use integrated timer to monitor all extended buses, and allow one master to isolate and communicate with slaves that may otherwise have address conflicts. They are specified over -40 to +85-

Signal Multiplexer for Device In-System Programming Coming Soon

January 15, 2009 - SMH Technologies announces today the development of a signal multiplexer for device in-system programming (MicroPlexer). Microplexer allows the ISP connection coming from the programmer/tester to be switched to one of the available output channels. In this way, a single programmer/tester can easily handle multiple device programming, whether on a single board or distributed...

Muxponder maximizes bandwidth on existing infrastructure.

Part of OpVista CX8 Optical Networking System, CX-40G Muxponder delivers 40 Gbps transmission/wavelength across optical networks from metro to long-haul. It is based on Dense Multi-Carrier (DMC) technology and combines 4 x 10 Gbs service streams into single 50 GHz Dense Wavelength Division Multiplexing (DWDM) channel. System helps deliver multiple 10-Gbit/sec services and also eliminates issues...

Relay Scanner/Multiplexer is mobile and USB-powered.

Measuring 5 x 7 x 1.3 in., SMU4032 USB Switching Module lets users maintain 7-½ digit measurement accuracy across switching architecture. Instrumentation specifications enable 6-½ or 7-½ digit DMM to deliver its full accuracy, and 35 differential inputs offer configuration flexibility. Along with thermal EMF errors of less than 1 -µV, features include isolated power and relay drive,...

IP System carries Ethernet and TDM data over same link.

Comprised of antenna, network management system, indoor and outdoor units, Microwave IP Solution allows for packet, hybrid, and classic data transport. It provides cellular backhaul service with both legacy Time Division Multiplexed and native Ethernet at 100 Mbps. Featuring full-duplex connection capacities of 34 Mbps of fast Ethernet interface, system works across 7-23 GHz frequencies, and is...

Don't Let Your Money Drain Down the Hole...Drill Steel with Euroboor

As a globally recognized manufacturer of industrial grade portable tools, Euroboor is at the forefront of drilling and cutting technology. Our reputation as an industry leader is built on robust products that fit a wide range of industrial cutting and drilling applications. See our video to learn more about all of our quality products.