Gate Valves

Gate Valves

Slide Sleeve Valve provides on/off control of gas or liquid.

Operating in in-line configuration, ultra-miniature, M3 threaded Model M3SV-N can be attached directly in fluid circuit and does not require panel mounting. Two-way, non-venting device is 0.78 in. long from end to end with no preferred flow direction. Maximum inlet pressure is 250 psig, and approximate flow orifice is 0.024-0.028 in. diameter. Available in brass or stainless steel, valve features...

Read More »
Knife Gate Valve suits severe service applications.
Gate Valves

Knife Gate Valve suits severe service applications.

Fabri-Valve XS150 features full port and one-piece perimeter seal that is double-locked in valve body, providing bi-directional, bubble-tight shutoff. Tab on perimeter seal acts as body joint seal, which eliminates possibility of joint leakage caused by pipe stresses. Should packing leak, valve is repairable while under line pressure. New packing can be injected into valve without shutting system...

Read More »
Knife Gate Valves suit slurry or abrasive services.
Gate Valves

Knife Gate Valves suit slurry or abrasive services.

With modular design, Vic-Knife Series 793 and 797 are equipped with interchangeable ends to accommodate IPS carbon, grooved, or plain-end steel pipe or plain-end HDPE pipe. Both series employ straightforward design, one set of bolts, and carbon steel body plates with flush port option at bottom of valve. Rated to 150 psi, products are available in 3-12 in. sizes with handwheel; gear operator;...

Read More »
Custom Valves suit chemical and nuclear industries.
Gate Valves

Custom Valves suit chemical and nuclear industries.

Valve types include slide, double slab gate, gate, ball, plug, glob, piston, tank bottom, sampling, injection, rinsing, and butterfly valves. They are offered as manual or automatic, pneumatic, electric, and hydraulic, in sizes -½-48 in., with pressure classes from ISO PN 10-420. Valves can be manufactured from carbon steel, austenitic and super austenitic stainless steel, duplex steel, nickel...

Read More »
Knife Gate Valve has dual actuators.
Gate Valves

Knife Gate Valve has dual actuators.

Made of 2205 Duplex Steel, 48 in. valve handles corrosive and abrasive materials. Product has face-to-face dimension of 6 in. and assembles without welding. Controls automatically open and close valve to 85% of open position, allowing removal of material deposit on blade. Unit is controlled by 3 relays, 1 limit switch, and 1 timer, all appropriately interlocked. Solids accumulated on bottom can...

Read More »
Gate and Angle Valves suit high vacuum applications.
Gate Valves

Gate and Angle Valves suit high vacuum applications.

Aluminum gate and angle valves are suited for isolation of roughing lines and fore-lines in vacuum processes where high conductance is required. Gate valves (GVA) and angle valves (AVA) range in size from 2-24 in. and are offered with ASA flanges. When loss of power/pneumatic pressure occurs, valves close, isolating vacuum system. During servicing, valves remain in situ for removal of actuator...

Read More »
Gate Valve includes handwheel for easier operation.
Gate Valves

Gate Valve includes handwheel for easier operation.

Model 2286 is constructed of lightweight Pyrolite® with heavy duty wedge gate design and non-rising stem. Inlets and discharges are available in threaded 3, 3 1/2, 4, 4 1/2, and 5 in. or 4 and 5 in. storz. Design provides minimal friction loss (less than 1 psi at 1500 gpm), and meets NFPA slow close requirements. Model 2286 is suitable for use on hydrants, pumpers, and aerial applications.

Read More »
Solder Redefined
Sponsored

Solder Redefined

Indium Corporation has developed a new twist on traditional solder by developing a composite with a reinforced matrix internal structure. The result is a solder with increased strength and reliability. Check out this video to learn more about the mechanics behind the groundbreaking technology.

Read More »

All Topics