Electronic Amplifiers

Op Amps feature quiescent current of 45 µA at 1 MHz.
Electronic Amplifiers

Op Amps feature quiescent current of 45 µA at 1 MHz.

Featuring gain bandwidth product of 1 MHz, MCP6401/2/4 Op Amps complement eXtreme Low Power PIC® microcontrollers, helping to extend battery life in consumer, industrial, automotive, and medical applications. Small form factor units have max offset voltage of ±4.5 mV and operate from supply voltage of 1.8-6 V over extended temperature range of -40 to +125°C. Available in SC-70...

Read More »
Electronic Amplifiers

Monolithic Voltage Buffer Amplifier targets CCD applications.

Available in 1.6 x 1.6 x 0.55 mm LFCSP package, Model ADA4800 consumes 20 mW of static power and features fixed gain of 1. For CCD applications, active load current source can load open source CCD sensor outputs and buffer can drive AFE load. Active current load can also be switched off, allowing amplifier to be used as unity gain buffer. Employing push-pull output stage architecture, device...

Read More »
High-Voltage 40 W Power Amplifiers offer output up to ±2 kV.
Electronic Amplifiers

High-Voltage 40 W Power Amplifiers offer output up to ±2 kV.

Trek HV Amplifier Model 2205 controls output voltages from 0 to ±500 Vdc or output currents from 0 to ±80 mA peak AC, while Model 2210 controls output voltages from 0 to ±1 kVdc or output currents of 0 to ±40 mA peak AC. Model 2220 handles 0 to ±2 kVdc output voltages or output currents of 0 to ±20 mA peak AC. Regulated and controlled AC output signals, DC...

Read More »
Electronic Amplifiers

RF Front End Module suits ZigBee-based, ISM applications.

Front end module (FEM) RF6515 can improve performance of 2.4-2.5 GHz ISM band wireless applications requiring longer-range operation at high efficiency, including WLAN, Zigbee®, Smart Energy/Advanced Metering Infrastructure, and Home Area Networks. Supplied in 3.5 x 3.5 x 0.5 mm package, FEM integrates 20 dBm PA, harmonic transmit filtering, and DPDT switch as well as balun which provides...

Read More »
The Next Wave of Intelligent Design Automation
Sponsored

The Next Wave of Intelligent Design Automation

In the amount of time it takes to set up a meeting to discuss just one design, engineers can now explore designs exponentially. Generative design has catalyzed a paradigm shift in product development. This shift not only drastically decreases the time it takes to design a product. It also opens the door to design options that might never have been imagined by engineers on their own.

Read More »
Multichannel Charge Amplifier targets laboratory applications.
Electronic Amplifiers

Multichannel Charge Amplifier targets laboratory applications.

Intended for mounting in 19 in. racks, Type 5080A features modular design that allows expansion to 8 amplifier modules. Unit can accommodate both charge modules for piezoelectric sensors and dual-mode modules with charge/Piezotron® input, enabling acquisition of force signals as well as signals from sensors measuring pressure, torque, or acceleration. Featuring frequency range of 0-200+...

Read More »
Electronic Amplifiers

Integrated Front End Module enhances wireless applications.

Supplied in 3.0 x 3.0 mm QFN package, RF3482 front end module (FEM) integrates WiFi power amplifier with SP3T switch for 2.4-2.5 GHz ISM band applications. Integration of complete switch functionality enables routing of WiFi and Bluetooth® receive/transmit signals to 2 SoC transceivers. Additionally, SP3T switch can act as splitter to transmit or receive Bluetooth and WLAN signals...

Read More »
Current-Sense Amplifier delivers wide-input common-mode voltage.
Electronic Amplifiers

Current-Sense Amplifier delivers wide-input common-mode voltage.

Allowing direct measurement of current in power lines operating up to 70 V, Model TSC103 aids design of power management, monitoring, and safety equipment. Device accepts common-mode input from 2.9-70 V and offers selectable output gain of 20, 25, 50, and 100 V/V. Common-mode input can also be set from -2.1 to 65 V in dual-supply configurations. Operating from -40 to 125°C, IC has...

Read More »
Electronic Amplifiers

Plenum-Rated Audio Amplifier/Mixer removes random noise.

PlenumAmp PMA-245H features HummBuster technology to remove random noise that can enter classroom audio systems and eliminates ground loop hums caused by inadequate electrical grounds and noisy sound cards. Incorporated switches also allow flexibility in resolving ground loop issues. Ideal for above ceiling applications, dual input, 18 V, 45 W stereo amplifier/mixer measures 5.43 x 4.80 x 1.65...

Read More »
Electronic Amplifiers

Power Amplifier targets mobile PC and embedded applications.

Operating from 4.9-5.8 GHz, Model RF5616 features fully matched input/output design, integrated low pass filtering, and integrated 3-stage PA. Device offers voltage supply levels from 3.0-5.0 V, enabling linear output power of 18-21 dBm. Interstage power detector minimizes sensitivity to voltage supply, temperature extremes, and VSWR, while optimizing accuracy of closed loop power control. Housed...

Read More »
Class D Speaker Amplifier offers automatic level control.
Electronic Amplifiers

Class D Speaker Amplifier offers automatic level control.

Designed for battery-operated portable devices, 2.2 W MAX98500 integrates boost converter to provide constant output power. Class D amplifier is equipped with battery-tracking Automatic Level Control circuit that limits max output swing as supply voltage drops. ALC helps to avoid clipping and prevents battery voltage from collapsing. Housed in 2.1 x 2.1 mm WLP, MAX98500 accepts 2.5-5.5 V supply...

Read More »
Solder Redefined
Sponsored

Solder Redefined

Indium Corporation has developed a new twist on traditional solder by developing a composite with a reinforced matrix internal structure. The result is a solder with increased strength and reliability. Check out this video to learn more about the mechanics behind the groundbreaking technology.

Read More »

All Topics