Altera Offers Complete USB 2.0 Device Controller Solution

SAN JOSE, Calif., July 31 -- Altera Corporation (NASDAQ:ALTR) today expanded its intellectual property (IP) portfolio with the introduction of a complete USB 2.0 Hi-/Full-Speed Device Controller solution from System Level Solutions (SLS). This new solution is comprised of a soft IP core, software and class drivers, and SLS's Snap-On PHY daughtercards. The daughtercards are designed for use...

Read More »

Industrial Ethernet Solutions Most Ideal for PLC/SCADA System Integrators

Taipei, Taiwan, 5 July, 2007- Ethernet Direct Corporation, a professional and primary provider of Industrial Networking and communication solutions, is pleased to present a series of Industrial Ethernet solutions which are most ideal for PLC/SCADA system integrators. Ethernet Direct products have been deployed in various applications and are faster becoming a preferred choice for systems...

Read More »

GE Fanuc Announces Support for Alpha HVi Series of Servo Motors and Amplifiers for General Motion Applications

DSM324i Motion Control Solutions Offer Reliability, Accuracy and Small Size For Added Value CHARLOTTESVILLE, VA, JULY 5, 2007 GE Fanuc Automation, a unit of GE Industrial, today announced the support by the DSM324i motion controller for six Alpha HVi series servo models for use in general machine automation. The Alpha HVi series servos, flagship servo line for GE Fanuc's industry leading CNC...

Read More »

NAND Controllers suit mobile storage applications.

Featuring ECC engine, SST55VD020 ATA Flash Disk Controller and SST55LC200 CompactFlash Card Controller manage high-density NAND flash requirements. With Ultra-DMA host interface and intelligent NAND flash interface, controllers can operate up to 30 MB/sec for sustained write and read operations. Both support up to 8 chip-enables for NAND devices. SST SuperFlash-based embedded firmware allows for...

Read More »

Microcontrollers feature up to 4 KB memory and 24 I/O lines.

Offered in LQFP32 and SDIP32 packages, Series ST7LITE49M comes in Flash and pre-programmed versions, with 128 bytes of true EEPROM memory. Chips include configurable watchdog timer, 8-bit Lite timers with prescaler, and dual 12-bit auto-reload timers, which operate over 250 Hz to 4 MHz. Other functions include internal 8 MHz RC oscillator, 32kHz auto-wake up oscillator, and 10-bit ADC. Units are...

Read More »

GE Energy to Perform Plant-Wide Controls Upgrade for Saudi Electric Company Plant

GE Energy to Perform Plant-Wide Controls Upgrade for Saudi Electric Company Plant MADRID, SPAIN-June 26, 2007- GE Energy was chosen to conduct a turbine, generator and plant-wide control and protection upgrade by Saudi Arabian Engineering Co. Ltd. for the Saudi Electric Company - Southern Operating Area in Bisha, Saudi Arabia. GE Energy will replace the existing turbine control and excitation...

Read More »

Trusted(TM) Receives Prestigious Achilles(TM) Certification from Wurldtech Security Technologies

Trusted(TM) Receives Prestigious Achilles(TM) Certification from Wurldtech Security Technologies. Maldon, UK - 29th June 2007, The Trusted(TM) Safety Controller from ICS Triplex is one of the first safety controllers in the automation industry to receive the Achilles(TM) Controller Level 1 Cyber Security Certification from Wurldtech Security Technologies. In April 2007, ICS Triplex engaged...

Read More »

Cleaver-Brooks Announces ASHE Show Line up

Media and attendees invited to learn more about how Cleaver-Brooks supports hospital steam generation needs July 8-11 MILWAUKEE - June 28, 2007 - Maintaining sustained power sources and sterile environments while maximizing efficiency are top priorities for health care facilities. Cleaver-Brooks understands these key issues and has designed new products that will be showcased in Cleaver-Brooks...

Read More »

GE Fanuc Announces the Addition of Softing As Proficy Process Systems Technology Partner

Proven Technologies Provide Framework for Contemporary Solution For Hybrid and Continuous Process Control CHARLOTTESVILLE, VA, JULY 2, 2007 GE Fanuc Automation, a unit of GE Industrial, today announced that it has entered into an agreement with Softing North America of Newburyport, Massachusetts, to provide Foundation fieldbus connectivity to the upcoming release of GE Fanuc's new Proficy®...

Read More »

CNC Control accepts pressure and position commands.

Designed to control general industrial machines, 8-axis Power Mate i - Model H automatically selects and executes position control based on positional control command when no force is applied to axis, and automatically selects and executes pressure control based on pressure command when external force is applied to axis. Function is useful for performing press-fitting of pins, die-cushion of...

Read More »

All Topics