LCD Touchpad helps manage information on FloBoss(TM) computers.

Panel-mounted LCD Touchpad interface enables information retrieval, configuration, tuning, and troubleshooting for flow management systems without external interface. Transreflective/backlit/weather-resistant device identifies installed modules and automatically updates screen accordingly. Working in conjunction with ROCLINK 800 software, unit presents data in charts and graphs and features red...

Read More »

Ring Index Drives suit automated machinery applications.

Designed with large through-holes to accommodate variety of automated machinery and equipment, CAMCO® Ring Index Drives include Models 1100RNG, 1550RNG, 750RNG, and 2000RNG with nominal ring diameters of 1.0, 1.5, .75, and 2.0 m, respectively. Users can attach fixtures directly to dial ring, eliminating need for additional dial plate. Direct shaft-mounted motorized drive package features...

Read More »

PWM ICs drive brush and brushless DC motors.

Designed to drive 3-phase motors in 8.5-60 V supply range, Apex Precision Power(TM) SA306-IHZ and SA57-IHZ deliver up to 5 A continuous output current and peak output of 17 A, all housed in 64-pin Power Quad package measuring less than 2 cm square. Devices feature cycle-by-cycle current limit, which provides ability to precisely control motor current in real-time for each motor phase. Both models...

Read More »

Buck Regulator offers 6 MHz operation for portable devices.

Available in 1.3 x 0.9 mm, 0.6 mm high wafer-level chip-scale package, ADP2121, 500 mA regulator requires just 2 small capacitors and one inductor. Device automatically transitions to low quiescent current power-save mode during light-load conditions and operates at input voltages ranging from 2.3-5.5 V, suitable for Li-Ion, Li-Ion polymer cell, and multiple alkaline/NiMH cell applications. Fixed...

Read More »

Switching Regulator offers quiescent current of only 75 uA.

Operating on wide input range from 3.6-36 V with input transient protection up to 60 V, LT3682 is suitable for load dump and cold-crank conditions found in automotive applications. Switching frequency is user programmable from 250 kHz to 2.2 MHz, while 1.5 A internal switch can deliver up to 1 A of continuous output current to voltages as low as 0.8 V. Unit features low ripple below 15 mVP-P,...

Read More »

Voltage Regulators deliver low EMI and low radiated noise.

Meeting EMI and multi-gigabit SERDES specifications, LTM4606 and LTM4612 attenuate both radiated energy and conducted wideband harmonic energy. LTM4606 operates from 4.5-28 V input supply, regulates outputs from 0.6-5 V, and delivers up to 6 A to load. Operating from 5-36 V input supply, LTM4612 regulates output voltage of 3.3-15 V and delivers up to 5 A to load. Units are housed in 15 x 15 x 2.8...

Read More »

Flyback Controller can charge capacitors to 1,000 V.

Driving external N-Channel MOSFET, LT3751 can charge 1,000 -µF capacitor to 500 V in less than 1 sec, suitable for applications such as professional photoflash systems, RF security, and high voltage power supplies. It can be configured for primary-side output voltage sensing, without needing optocoupler. Unit features boundary mode control, VCC input voltage range of 5-24 V, programmable input...

Read More »

Buck and Boost Regulator operates from 2.5-36 V.

Suited for load dump and cold-crank conditions found in automotive applications, LT3570, 36 V, 1.5 A (ISW) buck and boost regulator combined with linear controller is available in 4 x 4 mm QFN or TSSOP-20E package. Synchronizable up to 2.5 MHz, product has minimum output buck voltage of 0.8 V, and maximum boost output voltage of 38 V. Other features included are programmable switching frequency...

Read More »

PNP-Based LDOs feature quiescent current of just 3 µA.

Including models LT3008EDC and LT3008IDC, LT3008 series of micropower PNP-based LDOs have input voltage ranging from 2.0-45 V with adjustable output voltage ranging from 0.6-36 V. Housed in 0.75 mm 6-lead DFN 2 x 2 mm package with backside thermal pad, external capacitors can be used without need of series resistance. They deliver up to 20 mA output current with corresponding low dropout voltage...

Read More »

PoE Interface Controller is IEEE 802.3af/802.3at compliant.

LTC4265 suits high-power powered device applications needing up to 25.5 W. Device has ability to recognize power sourcing equipment as either Type-1 hardware (802.3af) or Type-2 hardware (802.3at) and allocate power accordingly. Shutdown pin with signature corrupt provides flexible auxiliary support, and rugged 100 V MOSFET isolates controller and external DC/DC converter during detection and...

Read More »

All Topics