New Amplifiers Products

Fiber Optic Amplifier comes in compact package.

DIN rail-mountable SU16 Series includes high power/high sensitivity models, or ultra-fast models with up to 8 kHz switching frequency. Housed in slim 10 mm profile package, series' sensitivity can be fine-tuned via multi-turn potentiometer. Features include self-diagnostic LEDs and weak signal outputs, mutual interference protection, and tool-less fiber attachment. Scanning ranges are offered to...

Variable Gain Amplifier targets medical ultrasound systems.

Model AD8335 has 4 channels, each with ultra-low noise preamplifier, X-AMPÃ-® VGA, and gain control interface. Featuring single-ended input and differential or single-ended outputs, preamplifier provides accurate noise performance with active impedance match set by external feedback resistor. Available in 9 x 9 mm 64-lead LFCSP, Model AD8335 operates from single 5 V supply, consuming 92...

RF Power Amplifier targets 802.11b/g WLAN applications.

Suited for 2.4-2.5 GHz frequency band, Linear RF Power Amplifier Module, Model RMPA2453 offers Error Vector Magnitude of 2.5%. Unit internally matches input and output to 50 Ohms and provides on-chip power-sensing detector with 20 dB dynamic range and dual shutdown options to minimize power consumption. Utilizing Heterojunction Bipolar Transistor technology, amplifier is suited for WLAN routers,...

Amplifier drives high sampling rate A/D converters.

Model LT5514 850 MHz, programmable-gain, broadband amplifier exhibits output 3rd order intercept of 49 dBm at 70 MHz. It has 2nd and 3rd order distortion products lower than -87 dBc, while delivering 2 V peak-to-peak output into 200 ohm load. Variable gain is adjusted by on-chip, digitally controlled attenuator in combination with fixed gain amplifier. Unit is suited for 12- and 14-bit, 65 MS/sec...

Key Considerations When Choosing the Right Medical Device Development Experts: From Concept to Market

This eBook covers various factors to consider when selecting a medical device development partner to ensure proper guidance from concept to launch.

Instrumentation Amplifier has digital gain control.

Housed in SSOP-16 or DFN12 package, LTC6915 features 14 levels of digitally controllable gain that can be set up to 4096 V/V via parallel or serial SPI(TM) interface. Gain drift of 1 ppm/Ã-

Amplifier loads transducer data with single key stroke.

Model ML801B multi-channel amplifier module features TEDS identification. Digitally stored data is electronically transferred to amplifier, allowing it to select correct settings and start taking measurements. ML801B permits number of sub-channels to be reduced to 8, 4, or 2 as needed, giving corresponding sampling rates of 2,400 Hz, 4,800 Hz, and 9,600 Hz. All channels are measured synchronously...

Transimpedance Amplifier features 90 MHz gain bandwidth.

Suited for high-speed photodiode applications, Model OPA380 features 50 pA bias current, 6.4 mA quiescent current, and 2.7-5.5 V supply range. Unit's 90 MHz gain bandwidth enables transimpedance bandwidth of greater than 1 MHz in most configurations. As a result of 25 Ã-µV max offset voltage and 0.1 Ã-µV/C offset drift, dynamic range of 5 decades can be achieved. Applications include...

Microphone Preamplifier supports TEDS.

Featuring 7-pin LEMO connector, Ã-½ in. Model PRM905 can be used with both prepolarized and externally polarized microphones. It is characterized by wide frequency range and low noise floor. Low output impedance and high output current permit it to drive very long microphone extension cables. Unit is suited for acoustic engineers using analyzers which support Smart Transducer Interface IEEE...

Op Amps suit power sensitive applications.

Series OPA734 and OPA735 are 12 V amplifiers that use auto-zeroing techniques to provide 5 Ã-µV offset voltage and near zero drift. They feature 750 Ã-µA quiescent current, 200 pA bias current, 1.6 MHz bandwidth, and rail-to-rail output swing within 50 mV of rails. Series OPA734 includes shutdown mode, allowing device to be switched from normal operation to standby current that is less...

Amplifiers suit communication components testing.

Broadband amplifier models 400S1G4 and 450S1G3 work as driver amplifiers in testing wireless and communication components and subsystems and have full rated power across band. Former consists of 400 W, 0.8-4.2 GHz unit that can cover multiple frequency bands, while latter delivers 450 W from 0.8-3 GHz. Both models are 100% VSWR tolerant, have digital control panels for local and remote control,...

Does Your Parking Lot Make a Good First Impression?

To enhance its appearance by removing oil stains, Terminator-HSD uses micro bacteria to remove the stain without harsh chemicals, acids, or detergents. Check out the video to learn more.