WAGO Corp.

Germantown, WI 53022

PCB Terminal Strips handle high currents.
Compact 745 Series have current rating of 50 A, are available with pin spacings of 15 and 20 mm, and accommodate wire from #24 to #6 AWG. Four solder pins ensure terminal strips fit securely and guarantee safe and efficient current distribution. Jumpers can be used to loop through potentials or connect current circuits in parallel. Separate test slots can be accessed, even with wires connected.
Read More »
DIN-Rail Power Supply offers 85% efficiency.
Part No. 787-912 2 Amp/24 Vdc switch-mode power supply provides output power of 48 W and universal input voltage of 85 to 264 Vac. Output is electronically protected against short circuits and is equipped with automatic restart. Unit has been tested and approved to UL 1950, CAN/CSA C 22.2 No. 950-95 and IEC/EN 60 950, and meets EMI suppression requirements of EN 50 022 class B. Ambient...
Read More »
Terminal Strip uses spring pressure termination.
Cage Clamp Compact Series 742 PCB terminal block offers choice of either knife disconnect or automotive mini-fuse. It is available with one, two, or three conductors, has pin spacing of 5 mm, and handles wire range of 12 to 28 AWG. Series 742 also offers jumpering capabilities and use of test plugs.
Read More »
Terminal Blocks offer space savings with 1.08 in. profiles.
CAGE CLAMP COMPACT 870 Series DIN rail mount terminal blocks measure 1.08 in. from top of rail. They connect 28-12 AWG, and carry current ratings of 20/5 amps at 300/600 V. Suitable for use in electrical appliances and terminal boxes, CAGE CLAMP COMPACT 870 Series terminal blocks are available in feed-through and ground blocks, multi-level blocks, EExi, diode, LED, and surge suppression block...
Read More »
Terminal Blocks suit electric, closed housing applications.
Series 826 ground conductor terminal blocks ensure automatic and reliable contact to metal enclosure walls. Multi-pole, feedthrough terminal blocks are made from modular, factory-assembled, individual terminals with solid, single-part housing, which is protected against accidental contact. Series 826 blocks connect 28 to 12 AWG, and are rated at 32 A with rated voltage of 500 V.
Read More »
Terminal Blocks provide alternative connections.
253 Series printed circuit board terminal blocks have 2 push wire connections: one parallel to PCB and one perpendicular. Alternative connection allows electrical potential to be looped without additional terminal blocks. Solid conductors with cross section from 20 to 16 AWG can be connected. Series is rated at 500V, and carries load current of 10A. Pin spacing is 5 mm.
Read More »
Spring Terminator fits chassis-mount applications.
DIN rail-mounted 869 Series Cage Clamp Compact, with current rating of 20 A at 300V or 5A at 600V, connects 28-12 AWG. Screw-fixing and snap-in mounting options provide safe support to terminal strips. Terminal blocks are assembled into multi-pole terminal strips with standard numbers of poles or can be custom assembled to any length. Marking and jumping options are also available.
Read More »
Fieldbus Connector works in automation systems.
ECO Fieldbus Coupler, for applications with reduced I/O requirements has small, 8-bit microcontroller format, yet includes diagnostic and communications capabilities of 16-bit I/O SYSTEM 750 Series version. Coupler can be used with I/O nodes that have maximum 32 byte data sizes, including analog and specialty I/O modules.
Read More »
Terminal Blocks fit into small spaces.
880 Series are 5 mm wide, and are suitable for front entry wiring when DIN rail space is limited. 4-conductor blocks, part numbers 880-831-834 and -832, are available without shield contact; are UL-rated at 600V, 20A; and have separate test openings for test plugs. Also available are 2 and 3-conductor through terminal blocks, with or without shield contact. Additional features include separate...
Read More »
Programmable Field Controller offers distributed control.
Programmable Field Controller (PFC) combines fieldbus coupler functionality with that of PLCs. Users can store and execute programs locally, while still communicating I/O signals to and from network. Program execution continues, even if fieldbus connection is lost. Using IEC-1131-3 programming standards, programmers have access to all fieldbus and I/O data. PFC is available for Ethernet,...
Read More »