SKF USA Inc.
Lansdale, PA 19446
Pump Frame prevents premature bearing/seal failure.
Environamics universal power frame cartridge eliminates premature bearing and mechanical seal failures caused by heat, vibration, misalignment, and cavitation. Modular replacement for existing power frames bolts into place without modifying pump, piping, or foundation. Interchangeable shaft ends enable unit to fit any impeller configuration. Cartridge can be converted from standard power frame to...
Read More »
Toroidal Roller Bearings suit industrial fan applications.
CARBÃ-® bearings perform as non-locating bearings in self-aligning bearing systems for industrial fans. Compact, radial roller bearings compensate internally for angular misalignment and accommodate axial shaft expansion. Raceway profiles result in minimized frictional running and reduced operating temperatures. Used with same standard housings and accessories as other self-aligning bearings,...
Read More »
Steel Disk Seals protect roller bearings from liquids.
Type LST-L NILOS-Ring Seals offer protection for grease-lubricated roller bearings in applications where wash-down or regular exposure to liquids may be required. Stainless steel, non-contact labyrinth seals incorporate Viton-® gasket for extra sealing, especially when liquids are in permanent contact with bearings. With 4 mm profile, units come in range of sizes to accommodate various internal...
Read More »
Ball Transfer Units suit internal roller applications.
Miniature ball transfer units are utilized to perform material-handling and positioning functions for transfer of small parts or installed inside sensitive equipment to serve as alternatives to rollers. They allow for 360-º movement and have steel housings with steel/stainless balls and flat/angled tops. Depending on type, units are available with ball sizes from 4.8-9.6 mm, weigh from...
Read More »
Fault-Detection System spots engineering problems in fans.
SKFÃ-® Copperhead for Industrial Fans spots emerging bearing-related problems to help prevent premature failures and unplanned downtime. Users can monitor fan vibration and temperature on continuous or periodic basis. Problems detected include fan unbalance, mechanical looseness, bearing misalignment, and inadequate lubrication. System includes Copperhead sensor, which combines vibration...
Read More »
Fault Detection System spots emerging problems in fans.
SKFÃ-® Copperhead for Industrial Fans, enables users to monitor fan vibration and temperature on continuous or periodic basis. It provides early warning of fan unbalance, mechanical looseness, bearing misalignment, inadequate lubrication, and other problems that can lead to premature bearing failure. Applications include process fans employed in cement, mineral processing, steel, metal...
Read More »
Bearing Controller and Assemblies suit high-speed equipment.
Providing bearing stability and precise positioning, MB240 digital control system consists of one 2 A, 40 W system with Adaptive Vibration Control. Custom-built to meet user requirements, Hyperspin spindles are multi-component magnetic bearing assemblies that incorporate radial and thrust bearings, housings, shaft, motor, and controller. Synchronous spindles are offered in speeds to 60,000 rpm...
Read More »
Bearings provide increased options for designers.
SKF Explorer Angular Contact Ball Bearings exhibit up to 3x longer service life than conventional angular contact bearings. Bearings come in single or double row designs. Single row bearings are for pumps requiring high speeds and heavy axial and radial loads. Double-row models have 30Ã-
Read More »
Ball Bearings suit high-speed spindle applications.
CX/ACX Series high-precision, angular contact ball bearings allow rotational speeds up to 1.8 Mndm and are available in various contact angles to satisfy required axial stiffness and load requirement ranges. With optimized internal geometry, products are suited for high-speed metal-cutting, woodworking, milling, and other precision machine-tool applications.
Read More »
Manufacturing Cell cuts aluminum, cast iron, and steel.
Module-Mation(TM) 3-Axis Manufacturing Cell uses reconfigurable elements including spindle, column position, way style, and compound X-Z or Z-Y. Module parameters include 500 mm Z-axis, 400 mm X-axis, and 400 mm Y-axis. Traverse rate is 950 ipm, acceleration rate is 80 in./secÃ-², and thrust is 3,000 psi. Module accepts 40 or 50 Milling Taper or HSK 63 tooling. Motorized spindle, belt-driven...
Read More »