Parker Hannifin Corporation

6035 Parkland Blvd.

Cleveland, OH 44124

Flare Fitting is available in various configurations.

Triple-Lok 2 incorporates precision-engineered O-ring groove that provides maximum sealing performance without weakening or compromising fitting nose. Groove prevents O-ring overfill and pinching and accepts standard O-rings in most sizes. Soft-seal, stainless steel, 37Ã-

Fluid & Gas Flow Equipment

Injection Lubricators feature positive displacement design.

Parker/Watts Single Point and Multi-Point Injection Lubricators inject oil into application, not air lines. User can dial in exact amount of lubricant for each application for every cycle. Single Point Model L50 delivers precise amount of oil to single device. Multi-Point Model PL50 lubricates from 1-10 points simultaneously when receiving single remote pilot signal. Options include cycle counter...

Sensors, Monitors & Transducers

Pressure Sensors provide response time less than 2.0 ms.

PARKER/CONVUM Pressure Sensors utilize piezoelectric technology and offer pressure ranges from -14.7 to 8,820 psi. They are suited for air or other non-corrosive gases, water, hydraulic fluid, or other non-corrosive liquids. Units provide NPN/PNP and analog outputs, up to 7-segment LED output displays, and up to IP67 rating. Outputs are programmable NO or NC and include Hysteresis and Comparative...

Fluid & Gas Flow Equipment

Lift Check Valves suit various laboratory applications.

With stainless steel forged bodies, LC-Series valves withstand temperatures from -100 to +900 Ã-

Agricultural & Farming Products

Poultry-Picking Fingers reduce physical marking.

Yellow Poultry Picking Fingers provide resistance to abrasion and premature breakage. Fingers meet all FDA White List requirements for 21 CFR177.2600 and are offered in 5 different hardness grades. Service life is increased by up to 300% over traditional black rubber compounds. Yellow compounds eliminate post-cure surface tack and enable fingers to resist cut growth that often occurs as they are...

Fluid & Gas Flow Equipment

Ball Valve suits high-pressure applications.

Suited for operation at pressures to 10,000 psig, Hi Pro valve utilizes 2-piece construction to minimize potential leak paths. Bidirectional valve, fabricated from 316 stainless steel, is available in 1/4, 3/8, and 1/2 in. sizes or 6, 8, 10 and 12 mm metric versions. Design conforms to ANSI/ASME ratings and features 4:1 pressure boundary safety factor. Valve mechanism works on floating ball...

Fluid & Gas Flow Equipment

Ball Valve features quick-on, quick-off control.

Series B12 bi-directional, high-flow valve has spring-loaded ball seats and blowout-resistant stem. It is pressure rated at 4000 psig CWP. Micro-finished ball provides positive seal. Stainless steel valve offers 2-way inline body configuration and .50 in. orifice. Manual, pneumatic, and electric actuation is available. Port connections are FNPT, CPI(TM) single-ferrule, and A-LOKÃ-®...

Mechanical Components and Assemblies

Seals perform in temperatures up to 300-

XHNBR carboxylated nitrile seals exhibit high tensile strength, high heat resistance, and resistance to hydrogen sulfide, corrosion inhibitors, steam, oil, and other chemicals. They are also highly resistant to wear, abrasion, and extrusion. XHNBR Seals are suited for downhole oilfield, reciprocating and rotary drilling system uses, and other energy, oil and gas operations.

Fluid & Gas Flow Equipment

Valve Doors reduce contamination in semiconductor processes.

UHP Ultra-High Purity slit valve and gate valve doors feature fluorocarbon or perfluorinated elastomer seals, chemically bonded to aluminum or steel. UHP Gate Valve Door(TM) provides OEMs and chip fabricators with original and/or replacement door offering abrasion resistance and seal integrity. UHP Slit Valve Door(TM) reduces potential contamination by up to 95%, while increasing wafer yield by...