Parker Hannifin Corporation
Cleveland, OH 44124
Share:
Improved Gearheads handle heavier loads, last longer.
Stealth PS in-line and RS right-angle helical planetary gearheads have greater face width for higher load capability, smoother tooth engagement, and lower backlash. Stealth Advanced Gearhead has been improved to reduce heat and increase internal lubrication that will extend seal and gearhead life. Other enhancements include smaller viton seals to reduce start up torque and increase efficiency,...
Read More »
Lockout Valves have integrated soft-start functions.
EZ Series Lockout Valves comply with OSHA Standard 29 CFR Part 1910, and prevent accidental actuation during servicing of air-operated equipment. Valves are offered in pipe sizes from 3/8 to 1 1/4 in., with BSPP and NPT threads, and CVs from 3.7 to 13.7. Exhaust ports range from 3/4 to 1 1/4 in. Construction consists of cast aluminum-alloy body, detented spool, and threaded exhaust port....
Read More »
Hydraulic Hose exceeds SAE 100R2 requirements.
Jack Hose is for hydraulically powered jacking equipment that uses petroleum-base hydraulic fluids. It has maximum working pressure of 10,000 psi, high Nitrile inner tube, and twin braids of high-tensile steel wire reinforcement. Oil-, weather-, and abrasion-resistant, black, synthetic-rubber cover is MSHA accepted. It is fully functional within temperature range of -40 to +160 deg F. No-Skive...
Read More »
Ball Valve provides easy access.
Three-Piece Swing-Out Ball Valve provides direct access to internal seals without disturbing pipe alignment. Seal replacement is performed by removing one body bolt, loosening other three, and swinging out center section. Valve body is made from CF-8M stainless steel and is available in female pipe sizes from 1/4 through 2 in. Working pressure is 1000 psi and temperature range is 0 to 400 deg F.
Read More »
Seals require low closure force.
FF354-65 white perfluorinated elastomer (FFKM) seals offer low durometer of 65. Soft properties allow for installation of o-rings and other seals into groove shapes such as dovetails and radius corner designs. FF354-65 seals resist compression set and offer temperature resistance up to 600 deg F. Chemical-resistant material is suitable for use in semiconductor fabrication, pharmaceutical...
Read More »
Stainless Steel Ball Valves offer corrosion resistance.
Series 500 is available in female pipe end configuration with standard 1/4 turn lever handle, Slide-Lock locking handle, short and oval handles, panel mount, and with 360 deg welds on retainer nuts. Other configurations include male-female pipe end, 1/2 in. 90 deg ball valve, and sweat-end ball valves for use on tubing. All valves feature full port design for unrestricted flow, with reinforced...
Read More »
Pneumatic Fittings simplify motion control.
Blocking fittings mount on air cylinder port and use independent pilot air signal to block movement of piston rod at selected positions. Slow Start fittings control speed at which cylinders recover position. Flow Control Regulators are unidirectional and adjust speed of cylinder rod by controlling inlet or outlet flow. Inline Flow Controls mount anywhere and can be ganged together. Right Angle...
Read More »
Fittings have working pressure up to 300 psi.
Prestolok(R) 1-piece brass fittings accept polyethylene, nylon, or soft metal tubing. Elastic metal grab ring grips tubing securely, and nitrile O-ring forms positive seal. Once in fitting, tubing can rotate freely, even under pressure. Swivels on male pipe threaded shapes permit precise positioning and installation in tight spaces.
Read More »
Ball Valves are panel mounted.
P506 Series is made from CF-8M stainless steel and is available in 1/4, 3/8, and 1/2 in. sizes. All have working pressure of 2000 psi and temperature range from -50 to +450 deg F. Valves mount to surface such as control panel and can be used with pneumatic actuator in remote location. Applications include off-shore drilling platforms, machine tools, packaging and paper making equipment,...
Read More »
Mini Ball Valves for use in confined spaces.
Brass mini ball valves are rated at 300 psi and have working temperature range of 0 to 250 deg F. Extruded brass body is nickel plated with 1/4 turn handle for positive full shutoff. Valves have blowout proof stem, hard chrome plate ball, and TeflonÃ-® seats. They are available in 1/4, 3/8, and 1/2 in. female/female sizes.
Read More »