Aprima Medical Software, Inc
Carrollton, TX 75006
Share:
Impact Socket Sets offer access and versatility.
3/8 in. Drive Semi-Deep Impact Socket Sets come in both metric and fractional sizes. Semi-deep sockets incorporate deeper broach depth than standard length sockets, and utilize fully tapered, nose down design. Both sets come packaged on metal rails. Ten piece fractional set (#4060) includes sizes from 5/16 to 7/8 in., and 12 piece metric set (#4080) includes sizes from 8 to 19 mm. All impact...
Read More »
Rotary Air Compressor reduces energy consumption.
Compressor's hybrid permanent magneto HPM synchronous motor features independent coil modules that can be removed and serviced. HPM motor directly drives compressor, eliminating need for motor bearings, gears, pulleys, belts, couplings, or motor shaft seals. With fewer components to wear out, leak or get out of alignment, compressor offers increased reliability and simple maintenance.
Read More »
Evaluation Board comes with Ethernet and audio module.
SAM-2104 StrongARM Demo Kit is built on Intel's StrongARM architecture, and measures 3 x 5 x 0.8 in. Its Intel StrongARM SA-1110 mini-BGA 256-pin module CPU operates at 206MHz. System memory is comprised of 32MB onboard SDRAM with storage provided by Compact Flash Type II socket. SAM-2104 has 1 USB port to support endpoints at 12Mbps (half-duplex) and 1 serial port UART that permits data transfer...
Read More »
Tilt Trays are made of ABS plastic.
Replacement Tilt Trays for sorters are thermoformed from 3/8 in. thick ABS plastic, and feature chemically-bonded back lip for additional strength. Weighing 9.2 lbs each, virtually unbreakable tilt trays are available to fit sorters manufactured by Alvey, Buschman, Crissplant, Dematic, HK Systems, Kosan, and Matthews. Trays are drilled to OEM specifications for direct replacement.
Read More »Panel Meters are available with 3 digit heights.
Available in packs of 10, Value Series panel meters include three, 3-1/2 digit LCD voltmeters with digit heights ranging from 0.25 in. (V1) and 0.50 in. (V125) to 0.63 in. (V600). Modules have 200mV full scale reading, user-selectable decimal points, fixing kit, and mounting bezel. Evaluation kits containing 1 of each module and test board are also available.
Read More »
Wire Partition System provides seamless integration.
WireWall wire partition system integrates with company's line of structural mezzanines. Standard and custom panel sizes are designed to avoid interference with columns and joists. WireRail panels are available to replace standard guardrail configuration at deck level. Flexible, sturdy design is suitable for storage areas and secured enclosures. Installation may be accomplished by 1 individual...
Read More »
Hoses handle high impulse and pressure applications.
471TC and 471ST high-impulse hoses, available in sizes from 1/4 to 1 in. ID, feature oil-resistant, Nitrile-based synthetic rubber tube and 2 braids of high-tensile steel wire reinforcement. Users can select level of abrasion resistance by specifying MSHA-accepted synthetic Tough Cover, or polymeric Super Tough Cover for severe environments. Hoses work with Parker's 43 Series fittings and...
Read More »
Junction Boxes feature single door style with clamps.
HV Series High Voltage Junction Boxes are available in stainless steel 316L and 304 and polyester powder-coated carbon steel. Enclosures resist impact and prevent possibility of excessive heat and ingress of water or dust, preventing explosions. 1 x 1 Connection Series is for shielded or unshielded cables up to 8kV at 500A, while 2 x 2 Connection Series is for 2 parallel, unshielded cables up to...
Read More »Coatings protect metal and refractory surfaces.
Corr-Paint(TM) coatings are designed for use from 200Ã-
Read More »
Machine combines shearing, press-braking, and rolling.
TRI-FAB Model 52P features shearing and rolling capacity of 52 in. x 12 ga mild steel and press braking capacities of 12 ga at 36 in. and 14 ga at 52 in. Machine will cut stainless steel up to 0.072 in. Rotating shafts are journalled in bronze bearings, and shear blades are Grade T10 tool steel. Manually-operated back gauge is standard, and can be positioned for use with shear or press brake as...
Read More »