Aprima Medical Software, Inc
Carrollton, TX 75006
Share:
Bandsaw Blades are offered in many varieties.
Bimetal and carbide blades include 3861 Sandflex(R) NF(TM) in 1/4 to 1 in. sizes, 3854 Sandflex(R) King Cobra(R) PHG(TM) in 2 and 2.5/8 in. widths, and 3851 Sandflex(R) Cobra PSG(TM) ground-tooth bimetal blades in 2 in. width and .050 in. thickness. Carbide blades include four versions of 3868 Fine Pitch Combo(R) blades with Triple Set(R) Xtra design with widths of 1 1/4, 1 1/2, and 2 in. and...
Read More »
Load Transfer System provides high-speed trailer loading.
Load Transfer Station uses configuration that combines pallet stacker, pallet dispenser, and output conveyor. It provides trailer-loading at speeds up to 50 loads per hour. Pallet dispenser handles 20 GMA pallets or 17 CHEP pallets. Single driver can feed loads to LTS while, simultaneously, forklift can pick up loads coming off output conveyor. Rugged construction withstands punishment of...
Read More »
Test Socket eliminates co-planarity problems.
BGA test socket has guided contact plunger that makes contact on periphery of solder ball, and maintains perpendicularity. Tapered cup design makes contact on angle and does not touch spherical radius of solder ball on bottom. Device features Rollerball(R) SMT technology and is available with solder tails for through-hole mounting. It is also available in 1.27, 1, 0.8, and 0.75 mm pitches.
Read More »
DC Motor meets global OEM needs.
Reliance C500/GS315 provides flexibility to meet either NEMA or IEC dimensional requirements. Four-pole configuration in square, laminated frame improves commutation and heat dissipation. Cast-iron end brackets, with integral mounting feet, put load-carrying members in same vertical plane to eliminate vibration. Motor is available through 800 hp and suits metal, paper, petrochemical, converting,...
Read More »
Dimming Ballasts offer 1- or 2-lamp operation.
Mark VIIÃ-® 0-10 V Dimming Ballasts are for use with T5/HO fluorescent lamps, including 54 W linear lamps, 55 W circline lamps, and 55 W long twin tube lamps. They operate on 120 or 277 V systems. Units dim lamps directly from compatible 0-10 V controls, including occupancy sensors and ambient light sensors. They include programmed-start lamp ignition, THD below 10%, end-of-life protection...
Read More »
I/O Board provides change-of-state detection.
Model 104-IIRO-8, an isolated, digital-input and relay-output board, installs in any standard PC/104 motherboard slot or stack. Eight-channel board has 60 V optical isolation on input lines, and standard Form C SPDT relay outputs. Isolated, non-polarized inputs may be driven by dc sources of 3 to 30 V, or ac sources at frequencies of 45 Hz to 10 KHz. Board operates in 0 to +50 deg C and 0 to 90%...
Read More »
Flow Switch offers response time of 1 to 10 seconds.
GT10 Thermo-Flo(TM) Gas Flow Switch provides flow detection and switching from 1 to 90 fps. Setpoint can be changed with single-turn of adjustment knob, which doubles as LED indicator for flow/no-flow status indication. Short version probe is for use in ducting from 1/2 to 1 1/2 in., while longer version is applied from 2 in. up. All-plastic sensor construction is either PP/Ryton(R) or PVDF...
Read More »
Power Supplies are controlled remotely.
Single output, low noise, 300 W RKW series has remote on-off, remote voltage control from zero to maximum rated output voltage, and current balance terminal for parallel operation. Single dc outputs from 3.3 to 48 V with active power factor correction are provided from 85 to 264 Vac mains. Conducted and radiated emissions are suppressed to FCC Class B, EN 55011-B and EN 55022-B limits with no...
Read More »
Bladeless Blower uses little compressed air.
Round TransvectorsÃ-® use small amount of filtered compressed air to deliver large airflow for conveying, ventilation, drying, cooling, and vacuuming applications. High-flow, bladeless blowers can be used to blowoff or vacuum scrap, dust, and chips from machining; convey pellets or small parts; remove fumes and gases; or work in cooling and drying operations. Used in ducted and unducted...
Read More »