Aprima Medical Software, Inc
Carrollton, TX 75006
Share:
Power Chuck has thru hole to swallow parts.
Pull-back, 3-jaw Series PUB provides accuracy for finishing applications. It has high gripping forces, component length control, and repeatability of 0.0004 in. All sliding surfaces are hardened and ground. Enlarged thru hole makes it suitable for shaft work pieces, including gear shafts and axle shafts. Thru-hole diameters for PUB206, PLUB208, and PUB210 are 39, 50, and 72 mm, respectively.
Read More »
Bus Bar Contact connects and disconnects quickly.
For use with PowerPoleÃ-® 180 and SBÃ-®175 housings, 180 A bus bar contact attaches directly to copper bus allowing quick connect/disconnect of cables. Quick disconnect minimizes system assembly, replacement, or repair time. Contacts are made from solid copper, are silver plated, and are threaded to provide simple attachment to bus without need for special tooling. Bus bar contacts...
Read More »
Motion Control Software runs 4X faster than previous version.
Multi-tasking MintMT programming language includes motion control, I/O handling, communications, networking, and operator interface functions. It allows each task to be independent of each other, making it easier to split machine programming tasks among several engineers. Applications can be written in modular manner, allowing for code re-use and reducing programming time. Dynamic syntax checking...
Read More »
Tool and Cutter Grinder changes to new tool quickly.
The TX7 performs complete changeover of wheel pack, coolant system, workholding collet, and pallet in less than 3 min. because wheel packs and corresponding coolant manifolds are prepared off-machine. It has 24 hp, 10,000 rpm spindle, automatic wheel changer, 3,000 rpm headstock, and ToolRoom tool and cutter grinding software. Direct drive work head allows users to include cylindrical grinding...
Read More »
Machining Centers have twin spindles.
MCT 160 and MCT 250 both have twin spindles with dedicated B axis for each spindle, allowing simultaneous machining on four sides of two different parts. Both models have twin automatic toolchangers with servo-driven lift and rotate systems. Working envelopes for each spindle are 450 x 450 x 450 mm for MCT 160 and 690 x 690 x 520 mm for MCT 250. Maximum part sizes for the MCT 160 and MCT 250 are...
Read More »Servo Drives and Amps fit any motor or application.
Servo amplifiers and drives are available in custom designs to drive brushless and brush-type linear and rotary motors and actuators. Each can be customized with connectors, number of axes, power range, feature set, functionality, diagnostics, packaging, and I/O. Supply voltages range from 20 to 400 Vdc. Output current capability is up to 120 A peak. Various commands and interfaces are available.
Read More »
Impact Wrench has muffler for quiet operation.
Lightweight Snap-on IMC500 1/2 in. square-drive wrench fastens and removes lug nuts, bolts, and screws in quiet and open modes. In quiet mode, exhaust runs through handle, providing quieter operation. When job requires more power, technicians can bypass muffler and add more torque. At full power, wrench achieves 525 lb-ft of forward torque and 620 lb-ft of reverse torque. It weighs 4.4 lb and has...
Read More »
Microcontroller connects to CAN bus.
C8051F040 mixed-signal microcontroller has analog and digital peripherals, pipelined 8051 CPU, 64K bytes programmable FLASH and 4352 bytes RAM, and CAN 2.0B network controller. Peripherals include two 12-bit DACs, 12-bit 100 kSPS ADC, Ã-
Read More »
Barricade Light can be seen from long distances.
Battery-powered BX-12 Barricade Warning Light has 12 separate LEDs positioned behind 12 individual, magnifying diffusers within Lexan face lens, providing concentrated light output in one direction. It can be seen for up to 1000 ft in daylight and more than 1 mile at night. Light produces 60 triple-pulse flashes per minute, operates for up to 2000 hr, and is available with yellow, red, or clear...
Read More »
Field Analyzer monitors reaction chemistry.
MonARC has NEMA 4X enclosure with purge and pressurization for safe operation in Class 1, Division I and II production environments. It has FTIR technology and front touch panel computer that allows direct access to operation parameters, critical process composition measurements, and analyzer diagnostics. Options include DiComp(TM) diamond sensor sampling interface for obtaining toxic, corrosive,...
Read More »