Aprima Medical Software, Inc

3330 Keller Springs Suite 201
Carrollton, TX 75006

Collets extend tool life of carbide drills.

Suited for carbide drills 6 mm and smaller, DNA Collets (Dead Nuts Accurate!) provide consistent T.I.R. to extend tool life. They can be used with any standard ER 16 collet chuck.

Agricultural & Farming Products

Portable Unit removes air pollution.

PAPCE captures contaminants from painting overspray, welding and chemical fumes, sanding dust, and cleaning operations at work source. Its versatility in unenclosed spaces promotes safe and healthy work environments. PAPCE is approved by CA-SCAQMD.

Controls & Controllers

AC Drives eliminate dynamic braking resistors.

Models E7 HVAC and F7 Vector drives include High-Slip Braking (HSB) software that controls motor deceleration, reducing overall braking time. For high-inertia loads, HSB can provide braking torque in excess of 100% full load motor torque. HSB is achieved by modifying volts/hz pattern during deceleration to maintain enough motor slip so load energy is absorbed in rotor bars, stator windings, and...

Crimping Tool is offered in 3 styles.

OEM-type, 5-stage Crimping Tool crimps 20-12 gauge OEM (open barrel) automotive terminals. Combination Crimping Tool crimps 22-8 gauge, non-insulated terminals; 22-14 gauge insulated terminals; and 7 and 8 mm ignition terminals. Tool also strips and cuts wire and cuts screws. Suited for battery terminals, Die Cast Terminal Crimping Tool handles all die cast terminals and lugs, 6 through 4/0...

Resetter enables refilling of Epson cartidges.

Within 6 seconds, No. R8 electronic reset device resets lock-out chips on cartridges to read full by joining contacts on resetter with those on cartridge's smart chip. Unit refills Epson T036 and T037 cartridges as used in Stylus C42UX printers. Resetter includes 3-year-life batteries capable of resetting hundreds of cartridges. Unit is suitable for use by rechargers and end users wanting to fill...

Fasteners & Hardware

Nuts have anti-backlash feature.

Nuts eliminate minimal backlash between leadscrew and nut interface on linear actuators and are available in non-captive and captive designs. Made from self-lubricating thermoplastic or glass-reinforced resin, nuts are available for .218 and .250 in. dia screw. Range of preload requirements can be accommodated up to 15 lb. Spring preload design assures precision over millions of cycles.

Fluid & Gas Flow Equipment

Booster Systems suit aircraft ground support applications.

Available in 1- and 2-stage models, portable nitrogen booster systems include automatic stop feature (activated when gas supply pressure drops to minimum inlet rating). Turnkey systems can be operated by one person. Designed to operate from one gas source, regulator with gauge operates boosters' drive sections at pressures to 145 psi. Single stage models are for use in nitrogen charging to 3,000...

HVAC

Chiller has temperature stability of -

KodiakÃ-® recirculating chiller provides immediate response to setpoint change. Its controller allows pressure units (PSI and BAR) to be set independent of temperature units (Ã-

Electrical Equipment & Systems

Transmitters communicate in HART and Fuji protocols.

Intrinsically safe, explosion-proof Series FCX electronic transmitters measure, display, alarm, and output level, pressure, and/or flow data. Type All includes gage, absolute, differential pressure, flanged level, and remote seal models. Type Alle includes gage and differential pressure models. Accuracy is Ã-

Laboratory and Research Supplies and Equipment

Carbide End Mills cut ferrous, high temperature, and titanium alloys.

Multi-layer TiAlN/TiN/TiAlN-coated carbide grade KC633M offers resistance to wear and deformation when rough machining ferrous materials and high-temperature alloys. Multi-layer TiN/TiCN/TiC-coated grade KC625M is suited for non-ferrous materials, while KC635M TiAlN-coated material suits high-temperature alloys. Other grades include KP525M powdered-metal material, KH110M uncoated steel grade with...