Stainless Steel Coatings, Inc.
South Lancaster, MA 01561
Oct 31, 2005 STEEL IT® Low VOC Stainless Steel Coating is high solids, low VOC stainless steel epoxy system that complies fully with environmental regulations. System consists of barrier primer and 316L stainless steel finish that are durable and resistant to corrosive effects of oils, solvents, detergents, and salt water. Featuring metallic grey satin finish that will not chip, peel, or flake, they can be applied by brush, roller, and conventional and airless spray techniques.

Devcon
Danvers, MA 01923
May 04, 2005 Applied via brush, roller, or squeegee, Floor Saversâ„¢ coatings protect walkways, ramps, platforms, and walls against chemicals, solvents, hydrocarbons, acids, and alkalis. Gray, epoxy-based formulations attain functional cure in 24 hr. Products include self-leveling Epoxy Coatâ„¢ 7000 NonVOC; Epoxy Coat 7000 AR, which withstands sulfuric acid concentrations up to 98%; and self-leveling Epoxy Coat 6500 NonVOC. Epoxy Concrete Sealer is self-leveling and clear.

Enviroline Group (IECC)
Pompano Beach, FL 33069
Mar 18, 2005 Usable at temperatures down to 32ºF, Enviroline 375LT high-solids epoxy will cure in 5 days. Enviroline 376F-30LT and Enviroline 376F-60LT are 100% solid epoxy coatings that cure in 7 days at 20ºF or one day at 45ºF. Each epoxy is suited for use as lining for storage tanks, process tanks, pipelines, and concrete containment areas in petroleum, chemical processing, and wastewater industries.

Enviroline Group (IECC)
Pompano Beach, FL 33069
Mar 18, 2005 Enviroline 380 ultra-high solids, thick-film epoxy coating exhibits chemical- and solvent-resistance in addition to abrasion- and impact-resistance. It does not require preheating prior to application and is suited for tank and pipe owners as well as contractors.

Master Bond, Inc.
Hackensack, NJ 07601
Dec 09, 2004 Featuring thermal stability, 2-component EP21ARHT-1 is 100% reactive and does not contain any solvents or diluents. It has 2:1 mix ratio by weight and cures at room temperature. Exhibiting minimal shrinkage upon cure, product does not sag or drip on vertical surfaces. Designed to withstand thermal shock and abrasion, it adheres to metals, glass, ceramics, cements, woods, vulcanized rubbers, and plastics. Operating temperature range is -60 to +350°F.

Garon Products, Inc.
Wall, NJ 07719 1924
Oct 06, 2004 Tigershieldâ„¢ system has thick coating layers that withstand constant punishment. Self-leveling formula can be poured on and squeegeed out to smooth surface. Suited for spalled and damaged concrete, coating gets into small cracks and creates seamless floor that is impervious to dirt and bacteria. Tigershieldâ„¢ system complies with OSHA regulations, is VOC compliant, and approved for use by USDA and EPA.

Sherwin-Williams Co.
Cleveland, OH 44115
Aug 30, 2004 Dura-Plate® MT Epoxy, low-VOC, 2-component, bisphenol A, epoxy-amine coating, adheres directly to damp or dry metal surfaces. Low-odor coating can be applied without regard to dew point. It provides performance comparable to MIL-P-23236C, Type VII, Class 15b and 17. Epoxy is suitable for ships, including bilge areas, and other offshore and marine structures as well as oil and fuel storage tank interiors, pulp and paper mills, and water treatment plants.

Revere Products
Cleveland, OH 44135 0311
Jul 22, 2004 Designed for floors that experience extreme chemical conditions, Epoxy Novolac is chemical- and acid-resistant. It contains no flammable solvents, meets national V.O.C. emission standards, and emits no unpleasant odor. Providing years of protection against tough abuse, high-gloss epoxy finish is suited for use in high-traffic areas, chemical troughs, storage tanks, splash zones, and warehouses.

Garon Products, Inc.
Wall, NJ 07719 1924
Jun 30, 2004 Water-based Tigerskinâ„¢ provides abrasion-resistant epoxy finish to concrete, wood, and masonry floor surfaces. It cures to satin finish that protects against graffiti and wear and tear on floors, walls, masonry, ceilings, and other surfaces. USDA-approved product beautifies and strengthens old, worn floors. Urethane-based Hi-Glossâ„¢, suited for use as topcoat, gives added abrasion resistance and wet-look shine to Tigerskin surface.

Sherwin-Williams Co.
Cleveland, OH 44115
Apr 21, 2004 Dual-component Polysiloxane XLE combines properties of epoxy and polyurethane in one coat. Glossy, self-priming coating is VOC-compliant and isocyanate-free and dries in 1 hr to corrosion-resistant finish. Suited for application by brush, roller, and conventional or airless spray equipment, product may be applied directly to properly prepared steel or over inorganic, zinc-rich primers. It is suited for structural steel, tank exteriors, and piping.

Sherwin-Williams Co.
Cleveland, OH 44115
Feb 19, 2004 Krylon® Industrial Tough Coat® Rebar Green Epoxy creates protective coating that resists chipping and peeling, and guards against rust stain bleed-through when rebar is encased in cement or concrete. Available in 16-oz cans, high-solids formula adheres to most substrates. It is applied using EZ TOUCH® FANSPRAY® nozzle, which sprays in horizontal or vertical pattern.

Aremco Products, Inc.
Valley Cottage, NY 10989
Dec 01, 2003 Corr-Paint™ CP2070 high-temperature, epoxy-novolac paint is a 2-part, gray-pigmented, 100% solids system used to protect steel components and structures. It is resistant to wide range of chemicals, and provides thermal shock, salt spray, and UV resistance. Mixed viscosity is 800–1000 cp. Applied by spray equipment, brush, or roller, coating dries and cures fully at room temperature in 24 hr. Typical film thickness is 5–7 mils for single coat.

Garon Products, Inc.
Wall, NJ 07719 1924
Aug 22, 2003 Non-shrink TREFLITEâ„¢ bonds to concrete, wood, steel, aluminum, glass, and ceramic surfaces to provide nearly indestructible finish to old and new floors. Resistant to thermal and physical shock, abrasions, acids, alkalis, and solvents, product also resists steel-wheel traffic with compressive strength of 14,000 psi. Resurfacer is 100% non-skid, even when wet, and no special tools or skills are required for application. Each 5 gal pail covers 40 ft² at 1/8 in. deep.

Electrolock, Inc.
Hiram, OH 44234
Aug 19, 2003 The E958-12A Epoxykits, pre-measured, 2-component epoxy coating system, allows for mixing of both components within provided package. Coating cures tack-free in 4–8 hr and obtains complete cure after 96 hr at room temperature. Product may also be fully cured in 5 min at temperatures of 212°F. Properties after cure include insulation resistance at 77°F at 1.1 x 1012 ohms and 82 Shore D hardness rating. Potlife is ~20 min, and shelf life is 1 year prior to mixing.

Sherwin-Williams Co.
Cleveland, OH 44115
Aug 06, 2003 Fast Clad® Edge Retentive Epoxy enables immersion service in 24 hr. Low odor, low-VOC, Bisphenol A amine coating offers greater than 70% edge build retention for corrosion resistance. When applied at 20.0 mils wet at 50% RH, the 98% solids tank lining is dry to touch in 1 hr and can be walked on within 4 hr. Designed for plural-component application equipment, product is suited for use over prepared steel surfaces.

Sherwin-Williams Co.
Cleveland, OH 44115
Jul 23, 2003 Fast Clad® Fast Dry (FD) Epoxy, formulated for quick recoat, can be applied at 4–6 mils dry film thickness at room temperatures as low as 40°F. This 2-component, high build polyamide epoxy can be recoated in 3 hr at 77ºF and is available in semi-gloss finish. Low VOC coating is chemical- and abrasion-resistant and can be applied to marginally prepared surfaces. It is suited for applications such as refineries and water treatment plants.

Sherwin-Williams Co.
Cleveland, OH 44115
Jul 17, 2003 Tank Cladâ„¢ HS provides interior lining for pipes and tanks containing potable water, fresh water, and salt water. It can be applied at temperatures as low as 40°F to tanks 1,000 gal and larger and to pipes 8 in. diameter or greater. With standard hardener, Tank Clad HS is certified for 60,000 gal and larger tanks and meets toxicological and extraction test requirements of ANSI/NSF Standard 61. Coating is 80% solids and complies with EPA standards for VOC emissions.

Sherwin-Williams Co.
Cleveland, OH 44115
Jul 16, 2003 Macropoxy® 646 NSF Fast Cure Epoxy is a fast-drying polyamide epoxy for steel and concrete structures. At 77°F and 50% relative humidity, it dries to touch in 2 hrs. Macropoxy® 846 NSF Winter Grade Epoxy is a fast-drying polyamide epoxy for industrial application maintenance and can be applied at temperatures as low as 35°F. It cures to touch in 4–5 hrs at 40°F, 50% relative humidity. Both are high solids, VOC compliant, and suitable for marginally prepared substrates.

Sherwin-Williams Co.
Cleveland, OH 44115
Jun 30, 2003 Fast Cladâ„¢ DTM, single-coat, direct-to-metal epoxy finish, provides high film build in one coat of 4–6 mils dry film thickness. Product dries to tough gloss finish, providing corrosion and chemical resistance as well as weathering protection. Applied at 77ºF, it dries to touch in 45 min and is dry to handle in 4 hr. Low-odor coating meets VOC and HAPS requirements, cleans up with water, and can be used directly over prepared steel.

Progressive Epoxy Polymers, Inc.
Pittsfield, NH 03263
Nov 22, 2002 Moisture-cured urethane MC 104, with zinc-dust additive, cures by reacting with moisture in air. It is applicable in shop or field by spray or rolling. With high solids content (82%), CM 15 ivory-colored epoxy is suitable for spray applications. It offers some internal flex to allow for substrate expansion/contraction. Gloss white Acrylic Poly 2-part acrylic polyurethane topcoat offers high gloss, UV protection, and abrasion resistance.