Mechanical Power Transmission

Mechanical Power Transmission

Servo Actuator has output speeds from 30-80 rpm.

February 27, 2002

PowerHub(TM) hollow shaft servo actuator delivers positional accuracy less than 1 arc min and repeatability of +/- 5 arc sec. Center through holes are available up to 27mm, allowing vacuum lines and wiring to be run through center of unit to external devices. Actuator is available in 2 sizes (-20 and 25) with ratios from 50:1. Output flange is supported by precision bearings, and output torques... Read More

Mechanical Power Transmission, Mounting & Attaching Products

Data-line Protectors operate beyond CAT 5 requirements.

February 27, 2002

Data-line Protectors offer full 20,000 watts of protection compared to industry norm of 1,500 watts. Units are tested repeatedly with 8/20 micro waveform at 6kV/3kA, without failure. Peak voltage seen at output is 33.2 V. Read More

Material Handling & Storage, Mechanical Power Transmission

Clamping Cylinder loads and unloads light parts.

February 27, 2002

Twist Clamp has internal mechanism to produce rotary piston motion throughout stroke. By attaching clamp arm, actuator becomes clamping mechanism for light-duty holding applications. Motion rotates clamp arm out of work area for easy loading and unloading of parts. It uses 40mm bore cylinder that produces up to 224 lb of clamping force at maximum pressure of 140 psi. Cylinder body is hard coat... Read More

Mechanical Power Transmission

Linear Bearing needs no lubricants.

February 27, 2002

One-Stop Shopping DryLin(R) linear bearing system consists of polymer-lined plain bearings with or without pillow blocks and DryLin(R) S aluminum shafting. It is suited for applications where lubricants are not desired, and wherever contamination due to dirt, dust, sawdust, lint or paper dust hinders operation of linear ball bearings. Read More

Mechanical Power Transmission

Front End Brakes offer IP65 protection.

February 27, 2002

Available for NEMA 23 and 34 sizes and designed specifically to plug in to Stepper or Servo Motors, SSB Series incorporates zero backlash permanent magnet brake and torsionally rigid coupling to accept misalignment. Brakes are also available in NEMA 42 size offering IP65 splashproof and dustproof protection. All 6 models include dual preloaded sealed bearings and black anodized aluminum housing. Read More

Mechanical Power Transmission

Torsional Couplings stop vibration, absorb loads.

February 27, 2002

LF, LK and LM solve torsional vibration problems common to internal combustion engine driven applications such as pumps, compressors and gen-sets. They absorb shock loads, accommodate misalignment, and handle shifting critical speeds safely above and below normal rpm operating ranges. All are non-lubricated and maintenance-free. Options include pump mounting plates and cast aluminum pump-mounting... Read More

Mechanical Power Transmission

Self-Lubricating Bearings are made with Teflon®.

February 27, 2002

PolyLube(TM) MRP self-lubricating composite journal bearings offer Teflon® fiber technology. They are able to withstand static loads of ~60,000 psi, and ~30,000 psi under dynamic loading. Fiber's oriented Teflon® multi-filaments are primary anti-friction components in bearing's ID. Heat-stabilized bearings have operating temperature range of +/-325°F, and may be used as new or... Read More

Controls & Controllers, Mechanical Power Transmission

AC Drive provides motor control in wash-down applications.

February 27, 2002

Model 160Z AC drive is designed for mounting on most standard AC motors. It offers NEMA 4X/IP65-rated protection and network connectivity. Drive is available with 4 different communication modules, including DeviceNet(TM), RS-232C, Profibus-DP and InterBus-S. It includes fault history for system diagnostics, elapsed time meter, feedback on specific drive and load conditions, and programmable... Read More

Mechanical Power Transmission

Linear Bearings are made from 100% polymer.

February 27, 2002

Drylin® RJI inch and Drylin® RJM metric polymer linear bearings are directly interchangeable with standard re-circulating ball bearings, and fit into standard pillow blocks. Made from iglide® J material, bearings have low coefficient of friction and shock and vibration dampening, require no external lubrication, and resist corrosion and wear. They are available from stock in standard... Read More

Mechanical Power Transmission

Dustproof Motor locks out contamination.

February 27, 2002

Abrasive Dustproof Series, sealed with built-in o-rings, has air fittings for pressurization up to 15 psi. Shaft slinger prevents abrasive dust from attacking shaft seal material, which in turn prevents dust from entering bearing. Motor is available in standard 23, 34, 42 and 65 frame sizes. Applications include industrial operations that use, produce or process powdered materials such as fiber... Read More

Mechanical Power Transmission

Drive Chain reduces workplace noise.

February 27, 2002

Low Noise Drive Chain offers spring roller construction, which absorbs impact of sprocket-chain interaction, reducing equipment noise by up to 10 decibels. It is available in sizes 40 through 80, and can directly replace ANSI standard chain for compliance with environmental management standards such as ISO 14000. Chain exceeds ANSI minimum tensile strength requirements and operates with standard... Read More

Mechanical Power Transmission

Stepper Motors have chrome platens.

February 27, 2002

Linear stepper motors travel at speeds to 80 in./sec, with strokes to 144 in. and acceleration to 1G. 2- and 4-phase linear steppers are capable of up to 50 lbs continuous force and 65 lbs peak force. Resolution of 2-phase motors is 1 full step equals .010 in., and 1 microstep equals .00004 in. Resolution of 4-phase motors is 1 full step equals .005 in., and 1 microstep equals .00002 in. Motors... Read More

Mechanical Power Transmission

Linear Actuators can be custom configured.

February 19, 2002

Electromechanical CATR actuators can be built using standard components such as motors, gears, screws, controls, and attachments to perform opening/closing, clamping/gripping, raising/lowering, or pushing/pulling functions. CATR 33 has ACME sliding screw for standard operation, CATR 33H has ACME screw, and CATR 32B has Ball screw. Options include stroke lengths, ac or dc motors, and friction... Read More

Mechanical Power Transmission

Speed Reducers withstand corrosive environments.

February 19, 2002

All-Stainless Steel Speed Reducers, with horsepower ranges through 5 HP, are available in frame sizes 918, 921, and 926 with quill-type 56C, 140TC, and 180TC NEMA C-face inputs. Construction consists of 304 cast stainless steel housings, covers, and shafts; stainless steel hardware; O-ring sealed C-face; and Mobile SHC 634 synthetic lubrication. Pressure compensation chamber prevents internal... Read More

Electronic Components & Devices, Mechanical Power Transmission

Brushless Amplifiers offer DSP-based sinusoidal performance.

February 14, 2002

SS100 and SS200 SimpleServo® digital brushless amplifiers range from 80 to 320 Vdc and 115Vac/230Vac, with peak currents ranging from 4 to 24 amps. Amplifiers can drive linear or rotary brushless motors with encoder feedback. SS100 accepts ±10V analog for controlling torque and velocity, and SS200 offers Step-and-Direction for controlling positioning. Most units have CE compliance and UL... Read More

Mechanical Power Transmission

Miniature DC Motors are 16mm in diameter.

February 14, 2002

16G88 Series DC ironless-rotor motors have continuous power rating of 4.5 W. They are available with choice of 6 windings for supply voltage from 3 to 24 V. Maximum recommended shaft speed is 12,000 rpm, and typical maximum continuous output torque is 5 mNm. All incorporate precious metal commutators and sleeve bearings. Matching 16mm dia planetary and spur gearheads are available with ratios... Read More

Mechanical Power Transmission

Vertical Pump Motor directly replaces less efficient motors.

February 14, 2002

Mod-Max meets NEMA premium motor efficiency standards, operates 0.8 to 4.0% more efficiently than company's older, less efficient motors, and can be used for VFD applications. Canopy cap requires no gasket and has 3 stand-offs to allow air circulation to help prevent moisture condensation. Winding includes pulse endurance wire. Each winding is also treated with 100% solids insulation material.... Read More

Controls & Controllers, Mechanical Power Transmission

Motor Starters are rated for hazardous locations.

February 12, 2002

Nelson combination starters are designed for starting and stopping single-speed, non-reversing squirrel cage motors at full voltage, utilizing either automatic or manual control. They protect against dangerous short circuits, while also serving as disconnect. Starters are built from copper-free cast aluminum with corrosion-resistant gray vinyl finish, and stainless steel cover bolts with captive... Read More

Mechanical Power Transmission

Couplings resist hostile environments.

February 12, 2002

CD Couplings include hub and bushing that have high chemical and moisture resistance in hostile environments. Hubs are precision machined steel. Couplings are available in Single Flex models, which provide misalignment up to 3 deg angular, 0.025 in. parallel, and 0.160 in. axial. Double Flex models provide misalignment up to 3 deg angular, 0.089 in. parallel, and 0.32 in. axial. Both models are... Read More

Mechanical Power Transmission

Clutch/Brakes start/stop loads to 1/2 deg per revolution.

February 12, 2002

CB Series Wrap Spring clutch/brakes, in 5 sizes, have rated static torque ranging from 25 to 2500 lb.in. and 1800 to 300 RPM maximum operating speed. Super CB Series, in 3 standard sizes, has rated static torque from 250 to 2500 lb.in. and 750 to 300 RPM maximum operating speed. Three models of WSC Series clutches are available in 5 sizes with rated static torque from 25 to 2500 lb.in. and 1800... Read More