Mactac
Stow, OH 44224
Share:
Adhesive suits pediatric and geriatric applications.
Ultra-Low Adhesion (ULA) adhesive exhibits low peel properties for use in short-term or sensitive skin applications. Offered in single or double-coated foam (TM6200), film (TM9730), and non-woven (TM9481) constructions, this hypoallergenic, medical-grade, pressure-sensitive adhesive is gentle and repositionable. Rubber-based formulation delivers cool, gel-like feel and maintains same peel...
Read More »
Coating System delivers precise, measured coverage.
MACdots coating system provides custom adhesive deposition in dot formation on liner for medical applications requiring direct skin contact over extended time periods. Each pressure sensitive adhesives (PSA) can be tailored for specific use in regards to breathability, application pattern, as well as size of dots and volume of adhesive deposited per dot for control of adhesion. Products employ...
Read More »
Double-Coated Film suits medical device assembly.
Type TM9720 consists of 0.5 mil clear polyester film carrier, semi-bleached kraft release liner, and hypoallergenic medical-grade adhesive. Product is suited for medical devices where skin contact is possible such as surgical drapes, diagnostic sensors, and dental dams.
Read More »
Pressure Sensitive Adhesive meets medical device guidelines.
Intended for medical devices where skin contact is possible, TM9616 consists of 1/16 in. white polyethylene foam, double-coated with acrylic-based, hypoallergenic, medical-grade adhesive. Adhesive is protected by semi-bleached kraft release liner with silicone release system on 2 sides. Product is formulated for sustained contact with human skin. Applications include ostomy mounts,...
Read More »
Pressure Sensitive Adhesives target electronic market.
MACbondÃ-® IR Series double-coated tapes offer high tack for solid bond. Moisture-stable liner keeps adhesive layer clean and flat, protecting against dust, dirt, and other particles. MACfilmÃ-® IF Series rubber and acrylic free films provide edge-to-edge bonding to variety of substrates. MACmountÃ-® IM Series double-coated, polyethylene foams are highly conformable and compressible,...
Read More »
Solar Control Film lowers energy consumption.
With metallized surface that blocks 99% of incoming ultraviolet rays, PermasunÃ-® can be applied to existing and new windows to reflect up to 68% of incoming solar heat and reduce glare by 64%. Product limits solar gain, fabric fading, and eye strain. Resistant to water, detergents, and alcohols, it is rated for internal or external applications on flat surfaces such as glass, polycarbonate,...
Read More »Light Block Films enhance rollable display color density.
ThermacolorÃ-® heat-activated, polyester films block out light and background colors in rollable displays and wall mount applications. Totally opaque backing products also lend depth and vibrancy to images and create edge frame for graphic images, posters, and printed materials. Products are available in 38 and 51 in. widths and 5 or 10 mil thicknesses. Suitable for use with hot-roll...
Read More »
Rubber-Based Adhesive is suited for automotive assembly.
With 12-point liner and polyester carrier, MACbondÃ-® IB-1185 performs general-purpose bonding applications, providing dimensional stability and die-cutting properties suited for automotive manufacturing. Product offers high-tack properties suited for bonding applications such as gasketing, sound dampening, and dust sealing.
Read More »
Pressure Sensitive Adhesive comes in several variations.
MACbondÃ-®, high-tack, double coated PSA allows for customization. Family of rubber and acrylic free films suits medium/high-energy surface bonding (IF-2010); high-temperature, aggressive adhesion (IF-2070); bonding to low surface energy materials (IF-2090); and very high-temperature applications (IF-3070). Suitable for mounting, bonding, and laminating, MACmountÃ-®, double-coated,...
Read More »
Bonding Tapes mount decorative parts in automotive interiors.
IF-2070 tapes are suitable for mounting nameplates, faceplates, die-cut parts, and decorative trim in auto interiors and are effective in bonding foams, felts, and fabrics. IF-2090 films bond to polypropylene, polyethylene and powder-coated surfaces. IF-3070 films are designed for high-temperature applications to 400 deg F.
Read More »
Adhesive suits pediatric and geriatric applications.
Ultra-Low Adhesion (ULA) adhesive exhibits low peel properties for use in short-term or sensitive skin applications. Offered in single or double-coated foam (TM6200), film (TM9730), and non-woven (TM9481) constructions, this hypoallergenic, medical-grade, pressure-sensitive adhesive is gentle and repositionable. Rubber-based formulation delivers cool, gel-like feel and maintains same peel...
Read More »
Coating System delivers precise, measured coverage.
MACdots coating system provides custom adhesive deposition in dot formation on liner for medical applications requiring direct skin contact over extended time periods. Each pressure sensitive adhesives (PSA) can be tailored for specific use in regards to breathability, application pattern, as well as size of dots and volume of adhesive deposited per dot for control of adhesion. Products employ...
Read More »
Double-Coated Film suits medical device assembly.
Type TM9720 consists of 0.5 mil clear polyester film carrier, semi-bleached kraft release liner, and hypoallergenic medical-grade adhesive. Product is suited for medical devices where skin contact is possible such as surgical drapes, diagnostic sensors, and dental dams.
Read More »
Pressure Sensitive Adhesive meets medical device guidelines.
Intended for medical devices where skin contact is possible, TM9616 consists of 1/16 in. white polyethylene foam, double-coated with acrylic-based, hypoallergenic, medical-grade adhesive. Adhesive is protected by semi-bleached kraft release liner with silicone release system on 2 sides. Product is formulated for sustained contact with human skin. Applications include ostomy mounts,...
Read More »
Pressure Sensitive Adhesives target electronic market.
MACbondÃ-® IR Series double-coated tapes offer high tack for solid bond. Moisture-stable liner keeps adhesive layer clean and flat, protecting against dust, dirt, and other particles. MACfilmÃ-® IF Series rubber and acrylic free films provide edge-to-edge bonding to variety of substrates. MACmountÃ-® IM Series double-coated, polyethylene foams are highly conformable and compressible,...
Read More »
Solar Control Film lowers energy consumption.
With metallized surface that blocks 99% of incoming ultraviolet rays, PermasunÃ-® can be applied to existing and new windows to reflect up to 68% of incoming solar heat and reduce glare by 64%. Product limits solar gain, fabric fading, and eye strain. Resistant to water, detergents, and alcohols, it is rated for internal or external applications on flat surfaces such as glass, polycarbonate,...
Read More »Light Block Films enhance rollable display color density.
ThermacolorÃ-® heat-activated, polyester films block out light and background colors in rollable displays and wall mount applications. Totally opaque backing products also lend depth and vibrancy to images and create edge frame for graphic images, posters, and printed materials. Products are available in 38 and 51 in. widths and 5 or 10 mil thicknesses. Suitable for use with hot-roll...
Read More »
Rubber-Based Adhesive is suited for automotive assembly.
With 12-point liner and polyester carrier, MACbondÃ-® IB-1185 performs general-purpose bonding applications, providing dimensional stability and die-cutting properties suited for automotive manufacturing. Product offers high-tack properties suited for bonding applications such as gasketing, sound dampening, and dust sealing.
Read More »
Pressure Sensitive Adhesive comes in several variations.
MACbondÃ-®, high-tack, double coated PSA allows for customization. Family of rubber and acrylic free films suits medium/high-energy surface bonding (IF-2010); high-temperature, aggressive adhesion (IF-2070); bonding to low surface energy materials (IF-2090); and very high-temperature applications (IF-3070). Suitable for mounting, bonding, and laminating, MACmountÃ-®, double-coated,...
Read More »
Bonding Tapes mount decorative parts in automotive interiors.
IF-2070 tapes are suitable for mounting nameplates, faceplates, die-cut parts, and decorative trim in auto interiors and are effective in bonding foams, felts, and fabrics. IF-2090 films bond to polypropylene, polyethylene and powder-coated surfaces. IF-3070 films are designed for high-temperature applications to 400 deg F.
Read More »